BoonDocker ARCTIC CAT: Non-turbo Control Box 700/800/1000 (V3) - Manual (Page 15)

BoonDocker – 1585 Hollipark Dr. Idaho Falls, ID 83401 – 208-542-4411 / 877-522-7805
www.boondockers.com – email: [email protected] – fax: 208-524-7381
Revised 12-14-07 Page 15 of 19
This mode adds nitrous and fuel when the button is pressed. When the button is pressed, nitrous will be
activated regardless of the TPS or RPM settings.
TUN:
Description: Btn
Fuel only :

TUN
When the handlebar button is pressed in TUN mode, only fuel is added. This is used to experiment
with fuel addition and subtraction while riding. Press the button at a certain rpm or under a certain load
to see whether your addition or subtraction is beneficial. This cannot be used in combination with N2O
operation. Be sure TPS and RPM triggering are OFF when using this feature.
CAP:
Description: Btn
StatCapture:

CAP
In CAP mode, the handlebar button is used to capture current data. When pressed, the Stats Capture
screen will be displayed and the data will be frozen when the button is released. After a capture,
pressing the Right-Arrow button will erase the captured data and return to Run Mode.
ARM:
Description: Btn
On for N2O :

ARM
By using a pushbutton (momentary), toggle, rocker, or slide switch connected to the button input, the
nitrous system can be armed or disarmed. When the switch is closed the system is armed and ready.
Then, depending upon other configuration settings, either the TPS or RPM with TPS can activate the
nitrous system. When the switch is open, the system is disarmed so neither TPS nor RPM will result
in nitrous activation.
Nitrous activation idea: One way to use the button for nitrous activation and to have the RPM limiting feature
(to prevent hitting the rev-limiter), set Btn to ARM, TPS to ON (with a low threshold), and RPM to ON (with
desired Min/Max settings).
Press the Left or Right Arrow to return to the N2O menu or push the “SEL” button to return to the Main
Menu.
C. N2O Configuration Examples
The following are examples of settings to achieve the various nitrous triggering configurations described in Section A
above:
1. Button only: Activate nitrous only
when the button is pressed.
Fuel TPS RPM Btn
040 OFF OFF

N2O
Set: TPS to OFF, RPM to OFF, and Btn to
N2O.
2. TPS only: Activate nitrous only
when the Throttle is pressed
beyond a set level.
Fuel TPS RPM Btn
040

200 OFF OFF
Set: TPS to ON (set the TPS threshold to the
desired level), RPM to OFF, Btn to OFF.
3. TPS and RPM only: Activate
nitrous only when the Throttle is
pressed beyond a set level AND
when RPMs are with a certain
range.
Fuel TPS RPM Btn
040 200

ON OFF
Set: TPS to ON (set TPS threshold to desired
level), RPM to ON (set Min/Max to
desired levels), Btn to OFF.
4. Button (N2O) or TPS: Activate
nitrous when button is pressed or
when Throttle is pressed beyond a
set level.
Fuel TPS RPM Btn
040 200 OFF

N2O
Set: TPS to ON (set TPS threshold to desired
level), RPM to OFF, and Btn to N2O.
5. Button (N2O) or TPS and RPM:
Activate nitrous when button is
pressed or when Throttle is pressed
beyond a set level AND the RPMs
are within a certain range.
Fuel TPS RPM Btn
040 200 ON

N2O
Set: TPS to ON (set TPS threshold to desired
level), RPM to ON (set Min/Max values),
and Btn to N2O.