Craftsman 917.293310 - Manual (Page 11)

i^CAUTION: Fill to within
V2
inch of top
of fuel tank to prevent spills and to allow
for fuel expansion. If gasoline is acciden’
tally spilled, move machine away from -
area of spill. Avoid creating any source of
ignition until gasoline vapors have disap­
peared.
'
Do not overfill. Wipe off any spilled oil or
fuel. Do not store, spilt or use gasoline
near an open flame.
TO START ENGINE
A.CAUT10N: Keep drive control bar in
“DISENGAGED* position when starting en­
gine.
When starting engine for the first time or if
engine has run out of fuel, it will take extra
pulls of the recoil starter to move fuel from
the tank to the engine.
, "
• Make sure spark plug wire is properly
connected. ’
• Move shift lever indicator to “N" (neutral)
position.
• Place throttle control in “FAST* position.
• Turn fuel shut-off valve 1/4 turn to OPEN
position. >
• Move choke control to CHOKE position.
• Grasp recoil starter handle with one
hand and grasp tiller handle with other
hand. Pull rope out slowly until engine
reaches start of compression cycle (rope
will pull slightly harder at this point).
• Pull recoil starter handle quickly. Do not
let starter handle snap back against
starter.
• If engine fires but does not start, move
choke control to half choke position. Pull
recoil starter handle until engine starts.
• When engine starts, slowly move choke
control to “RUN" position as engine
warms up.
NOTE: A warm engine requires less chok­
ing to start.
• Move throttle control to desired running
positiorh
• Allow engine to warm up for a few min­
utes before engaging tines.
Fueî shut-off Choke cxxitrols
Rewind starter
NOTE: If at a high altitude (3000 feet) or in
cold temperatures (below 40“ F), the carbu­
retor fuel mixture may need to be adjusted
for best engine perfomrance. See “TO
ADJUST CARBURETOR” in the Service
and Adjustments section of this manual.
NOTE: If engine does not start, see trou­
bleshooting points.
TILLING HINTS
A c AUTION: Until you are accustomed to
handling your tiller, start actual field use
with throttle in slow position (mid-way
between “FASr and “IDLE").
• Tilling is digging into, turning over, and
breaking up packed soil before planting.
Loose, unpacked soil helps root growth.
Best tilling depth is 4" to 6". A tiller will
also clear the soil of unwanted vegeta­
tion. The decomposition of this veg­
etable matter enriches the soil.
Depending on the climate (rainfall and
wind), it may be advisable to till the soil
at the end of the growing season to fur­
ther condition the soli.
• Soil conditions are important for proper
tilling. Tines will not readily penetrate
dry, hard soil which may contribute to
excessive bounce and difficult handling
of your tiller. Hard soil should be mois­
tened before tilling: however, extremely
wet soil will “ball-up” or clump during till­
ing. Wait until the soil is less wet in order
to achieve the best results. When tilling
in the fall, remove vines and long grass
to prevent them from wrapping around
the tine shaft and slowing your tilling
operation.
• You will find tilling much easier if you
leave a row unfilled between passes.
Then go back between tilled rows.There
are two reasons for doing this. First,
wide turns are much easier to negotiate
than about-faces. Second, the tiller
won’t be pulling itself, and you, toward
the row next to it.
• Do not lean on handle. This takes
weight off the wheels and reduces trac­
tion. To get through a really tough sec­
tion of sod or hard ground, apply upward
pressure on handle or lower the depth
stake.
11