Craftsman 247.79452 - Manual (Page 5)

For logs that are not cut square, the longest
portion of the log should be rotated down and
the most square end placed against the splitting
wedge.
Keep your work area clean. Immediately
remove split wood around your splitter so that
you do not stumble over it. Clean chips and dirt
off end plate (wood platform) after each tog is
split, or whenever necessary to maintain flat
contact between wood and end plate (platform).
Never move the tog splitter while the engine is
running.
Never leave your log splitter unattended with the
engine running. Shut off the engine if you are
leaving your splitter, even for a short period of
time. Someone could accidentally activate the
splitting wedge and be injured.
Do not run engine in an enclosed area. Exhaust
gases contain carbon monoxide. This odorless
gas can be deadly when inhaled.
Be careful not to touch the muffler after the
engine has been running. It will be HOT!
If the equipment should start to vibrate
abnormally, stop the engine and check
immediately for the cause. Vibration is generally
a warning of trouble.
When cleaning, repairing or Inspecting, make
certain all moving parts have stopped.
Disconnect the spark plug wire and keep the
wire away from the plug to prevent accidental
starting.
Customer Responsibilities
• Do not operate your splitter in poor mechanical
condition or when in need of repair.
• Periodically check that all nuts, bolts, screws,
hose clamps and hydraulic fittings are tight to be
sure equipment is in safe working condition.
Where appropriate, check all safety guards and
shields to be sure they are in the proper position.
Never operate your splitter with safety guards,
shields or other protective features removed.
These safety devices are for your protection.
• Replace all damaged or worn parts such as
hydraulic hoses and fittings immediately with
manufacturer approved replacement parts.
• Do not change the engine governor settings or
overspeed the engine. This increases the
hazard of personal injury. The maximum engine
speed is preset by the manufacturer and is
within safety limits.
• Do not alter your log splitter in any manner such
as attaching a rope or extension to the control
lever or adding to the width or height of the
wedge. Such alterations may cause your splitter
to be unsafe.
Perform all recommended maintenance
procedures before you use your splitter.
Do not service or repair your log splitter without
disconnecting the spark plug wire and moving it
away from the spark plug.
Never store the equipment with gasoline in the
tank inside of a building where ignition sources
are present, such as hot water and space
heaters, clothes dryers and the like. Allow the
engine to cool before storing in any enclosure.
Always store gasoline in an approved, tightly
sealed container. Store the container in a cool,
dry place. Do not store in a building where
ignition sources are present.
To reduce fire hazard, keep engine free of grass,
leaves, wood chips, and excessive grease and
oil.
The hydraulic system of your log splitter requires
careful inspection, along with the mechanical
parts. Be sure to replace frayed, kinked, or
othenwise damaged hydraulic components.
Fluid escaping from a very small hole can be
almost invisible. Do not check for leaks with your
hand. Escaping fluid under pressure can have
sufficient force to penetrate skin, causing
serious personal injury. Leaks can be located by
passing a piece of cardboard or wood over the
suspected leak and looking for discoloration.
Should it become necessary to loosen or
remove any hydraulic fitting or line, be sure to
relieve all pressure by shutting off the engine
and moving the control handle back and forth
several times.
.
Do not remove the cap from the hydraulic tank or
reservoir while your log splitter is running. Hot oil
under pressure could cause injury.
The pressure relief valve on your splitter is
preset at the factory. Do not adjust the valve.
Only a qualified service technician should
perform this adjustment.
Completely drain fuel tank prior to storage. This
guards against accumulation of fuel fumes
which could result in afire hazard.
Never store log splitter outside without a
waterproof cover. Rain will cause rust on the
inside of the cylinder.
Important Information
Always:
• Use clean fluid and check fluid level regularly
• Use Dexron III Automatic Transmission Fluid or
10W non-foaming hydraulic fluid.
• Use a filter (clean or replace regularly)
• Use a breather cap on fluid reservoir