Two-post rack installation – Cisco ASR 1004 User Manual
Page 8
8
Two-Post Rack Installation
The Cisco ASR 1004 Router can be installed in a two-post rack, either 19 inch or 23 inch.
Note
Inner clearance (the width between the inner sides of the two posts or rails) must be at least 19 inches (48.26 cm). The
height of the chassis is 1.73 inches (4.39 cm). Airflow through the chassis is from front to back.
Figure 4
Installing a Cisco ASR 1004 Router in a Two-Post Rack
Caution
If you are using a two-post rack secure the rack to the floor surface to prevent tipping and avoid bodily injury and
component damage.
Step 1
Position the chassis so the front is closest to you and lift it carefully into the rack. To prevent injury, avoid any sudden
twists or moves.
Step 2
With at least two people, slide the chassis into the rack, pushing it back until the brackets meet the mounting strips or
posts on both sides of the rack.
Step 3
Position the chassis until the rack-mounting flanges are flush against the mounting rails on the rack.
Note
To allow space to attach the cable management brackets to the chassis in the rack easily, make certain that you use
the rack-mount bracket ear holes specified in the next steps.
1
Rack-mount bracket ear and holes
2
Rack equipment rail
280178
MIN
AC
O
MAJ
STBY
ACTV
STAT
ASR1000-
RP1
PWR
CRIT
SPA-4XOC3
-POS
S
T
A
T
U
S
0
1
2
3
C
/A
A
/L
C/A
A
/L
C
/A
A
/L
C
/A
A
/L
SPA-4XOC3
-POS
S
T
A
T
U
S
0
1
2
3
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
SPA-4XOC3
-POS
S
T
A
T
U
S
0
1
2
3
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
SPA-4XOC3
-POS
S
T
A
T
U
S
0
1
2
3
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
SPA-4XOC
3-POS
S
T
A
T
U
S
0
1
2
3
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
SPA-4XOC
3-POS
ST
A
T
U
S
0
1
2
3
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
SPA-4XOC
3-POS
S
T
A
T
U
S
0
1
2
3
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
SPA-4XOC
3-POS
ST
A
T
U
S
0
1
2
3
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
C
/A
A
/L
BITS
CON
AUX
CARRIER
LINK
MGMT ETH
ERNET
DISK
HD
USB
DF
0
1
2
1