Two Brothers Racing Yamaha Grizzly 700 - Manual

Two Brothers Racing
Juice Box™ - Fuel Controller
2007-08 Yamaha Grizzly 700 Installation & Operation Manual
Part # 008-179
Parts Incuded
Installation Instructions
Qty. Description Part Number
1 Juice Box™ Fuel Control Kit 008-179
3 Zip Ties
1 Adhesive Velcro Square
V.A.L.E.
V a r i a b l e a x i s l o c k i n g e x h a u s t
TM
Route the JUICE BOX™ wires along the right hand side
of the ATV (Fig 6) and down between the fuel tank and
the cross member towards the injector.
Now locate the fuel injector from the left hand side of
the ATV (Fig 7).
Unplug the stock grey fuel injector connector. Plug the
JUICE BOX™ grey connector onto the injector and plug
the stock injector connector to the black JUICE BOX™
connector (Fig 7).
Attach the JUICE BOX™ ground wire (black) to one of
the fuel tank 10mm mounting bolts.
Start the ATV. The green LED should now be scrolling
for about 3-5 seconds and then go to 1-2 steady green
LED’s or a single slow flashing green LED. If the number
1 green and number 8 red LED’s continue flashing after
startup, an injector wiring error is indicated. Re-check
the wires from the JUICE BOX™ and make sure they
are connected to the proper wire of your ATV’s stock
harness. MAKE SURE you have the correct connectors
selected in the stock harness. DO NOT PROCEED
UNLESS ABOVE CONDITIONS ARE MET.
Reassemble the ATV.
NOTE: Re check your wire routing and JUICE BOX™
location and make certain that in no way the wires can
come into contact with any moving parts or high heat
source and that the JUICE BOX™ is mounted in a way as
to not cause a handling problem with the machine.
5.
6.
7.
8.
9.
10.
11.
IMPORTANT - PLEASE READ CAREFULLY
Warranty
two brothers racing warrants that this product carries a warranty for 2 years from date of purchase against original
defects in materials and workmanship. should this product fail to perform for either of the above reasons, two brothers
racing will repair or replace it with an equivalent product at no charge, except for postage, to the original retail purchaser.
to obtain the benefits of this warranty, the retail purchaser must return the product and proof of purchase to the place of
original purchase.
We recommend that this performance part be installed by a qualified ATV technician. If
you have any doubts as to your ability to install this performance part, please consult
with your local ATV dealer. Read all instructions first before starting installation. Make
sure the vehicle and exhaust system are completely cool before starting the installation.
Also, make sure the vehicle is secure during installation. Be sure to save all stock
components for possible use later.
The Juice Box™ is legal ONLY for closed course race vehicles. The Juice Box™ is not
applicable, nor inteded for use on EMISSIONS CONTROLLED street, highway or off-road
vehicles. The Juice Box™ is not applicable, nor inteded for use on aircraft.
Thank you for purchasing a genuine Two Brothers Racing
JUICE BOX™. This product represents a radical step
forward in tuning fuel-injected motorcycles and ATVs for
optimal performance using “load-based” technology.
We at Two Brothers Racing hope that you will find this
development as exciting and useful as we do. And
remember: Proper Fuel = Maximum Power!
Make sure the vehicle is completely cool before starting
the installation. Also, make sure the vehicle is secure
and will not roll around.
Remove the seat.
Remove the battery cover by lifting up (Fig 1), then
remove the 4 plastic fasteners from the fuel tank cover
(Fig 2) and remove.
Remove the plastic fasteners (Fig 3 & 4) and 4mm Allen
socket head (Fig. 5) from the left and right side panels,
along with the dipstick access panel. (Fig 4).
1.
2.
3.
4.
Tools Needed For Install
- Small Screwdriver
- 10mm Wrench
- 4mm Allen Wrench
Fig 1
Fig 2
Fig 3
Fig 4
Fig 5
Fig 6
Fig 7