Two Brothers Racing 2 in 1 Rear Service Stand User Manual
Two Brothers Racing For the car
Parts List
Care & Cleaning
This service stand features a “brushed” finish. To restore the finish use a scotch brite pad to remove any scratches.
Keep service stand free of dirt and moisture. Store in a cool, dry place. For cleaning use a mild spray cleaner.
Always apply cleaner or polish with a soft, clean cloth.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as
is” without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a
particular purpose and disclaims all responsibility for consequential and incidental damages or any other losses
arising from the use of these products or parts.
We recommend that this service stand be assembled
by a qualified motorcycle technician. If you have any
doubts as to your ability to assemble this service
stand, please consult with your local motorcycle deal-
er. Read all instructions first before starting assembly.
When using this service stand be sure the motorcycle
and exhaust system are completely cool.
1. Insert the stand legs into the stand hoop. Use the 8mm
x 65mm bolts, 8mm washers and 8mm nylock nuts to
secure. Be careful not to over tighten these bolts,
you will damage the stand if you over tighen these
bolts.
2. Insert the rear stand holder assemblies into the stand
legs. If your motorcycle used spools you will insert the
rear stand holder assemblies with the “V” pointing
inward. If your motorcycle does not use spools insert
the rear stand holder assemblies with the rubber pads
facing inward.
3. Adjust the width of the rear stand holder assemblies for
your motorcycle and tighten set screws. If your motorcy-
cle uses spools, the spools should sit in the cradle the
“V”. If your motorcycle does not use spools the
swingarm should rest on top of the rubber pads.
IMPORTANT - PLEASE READ CAREFULLY
2-in-1 SS Rear Stand Instructions.qxd
Non-Spool Detail
Installation Instructions
Care & Cleaning / Warranty
Stand Leg (x2)
Rear Stand Holder
Assembly (x2)
Stand Hoop
Hardware Box
Service Stand in the box/Arm Detail
Spool Detail
Flat portion on arm is for
set screw to hold arm.
Be sure this is properly
engaged before using
stand.
T
T
w
w
o
o
B
B
r
r
o
o
t
t
h
h
e
e
r
r
s
s
R
R
a
a
c
c
i
i
n
n
g
g
2
2
-
-
i
i
n
n
-
-
1
1
S
S
t
t
a
a
i
i
n
n
l
l
e
e
s
s
s
s
S
S
t
t
e
e
e
e
l
l
R
R
e
e
a
a
r
r
S
S
e
e
r
r
v
v
i
i
c
c
e
e
S
S
t
t
a
a
n
n
d
d
QTY.
DESCRIPTION
1
STAND HOOP
2
STAND LEGS WITH WHEELS
1
REAR STAND HOLDER ASSEMBLY - SPOOL / STANDARD
(SET: RIGHT AND LEFT, INCLUDES: ADJUSTABLE SWINGARM STOPS, AND RUBBER PADS)
1
ALUMINUM SWINGARM SPOOLS (PAIR)
2
8MM X 45MM BOLTS (FOR USE WITH SWINGARM SPOOLS)
1
5/32” ALLEN WRENCH (FOR ADJUSTABLE SWINGARM STOPS)
1
3/16” ALLEN WRENCH (FOR HOLDER ASSEMBLY ADJUSTMENT)
1
6MM ALLEN WRENCH (FOR 8MM X 65MM BOLTS)
2
8MM X 65MM BOLTS (FASTEN LEGS TO HOOP)
2
8MM NYLOCK NUTS
4
8MM WASHERS
2
SPARE SETS OF RUBBER PADS