Two Brothers Racing Suzuki DL1000 V-Strom - Manual

V.A.L.E.
V a r i a b l e a x i s l o c k i n g e x h a u s t
TM
Parts List
Installation Instructions
1. Make sure the bike is completely cool before starting the
installation. Make sure the bike is secure on the sidestand or
ideally a rear service stand.
2. Remove the passenger footpegs (left and right).
3. Loosen the clamps that holds the muffler connector pipes to the
headers.
4. Remove the hardware that holds the stock mufflers to the bike.
Be sure to remove the stock exhaust gaskets from the header as
you will NOT reuse it.
5. Assemble the V.A.L.E.™ assembly by attaching the muffler to
the X-Lite V.A.L.E.™ retaining ring and slip-on tube using the 4
6x14mm S.H.C.S. and lock washers provided. Keep loose for
now.
6. Place a bead of the hi-temp sealant on the outside edge of the
header that goes into the s-bends. Slide the S-bend connector
pipes onto the end of the headers, using the barrel clamps
to attach it to the headers. Leave loose for now. Wipe off the
excess sealant that will squeeze out.
7. Carefully slide the muffler clamps over the mufflers. You may
need to twist and turn the S-bend a little to get it in the right
place. Locate both tabs of the canister clamp outside of the
spacers. Use the hardware provided to secure it to the stock
mounting location. Leave loose for now.
8. Make sure everything is aligned and tighten all hardware.
9. Reinstall the passenger footpeg brackets WITHOUT the
heatshields attached.
10. Double check to make sure that all hardware is tightened.
11. Before you run the bike, clean off all fingerprints and dirt, as
any oily residue will etch the metal and become permanent
when the system gets hot. Also, remove any plastic film from
the name badge(s). Run the bike and enjoy. It is normal for
some white smoke to appear the first time you start the bike.
This is packing/manufacturing oil from inside the pipe burning
off. Check for gaps or leaks. If you find a leak, a little high
temperature silicon sealant should fix it. After 50 to 100 miles,
recheck all fasteners for tightness.
Qty. Description Part Number
1 Muffler Canister (Left Side) Varies
1 Muffler Canister (Right Side) Varies
2 Muffler Canister Clamps Varies
1 V.A.L.E.™ Slip Tube (Left) 005-4804NLV
1 V.A.L.E.™ Slip Tube (Right) 005-4804NRV
1 HARDWARE KIT 005-48-3
2 X-Ring Kit 005-7-2-3KIT
2 8x70 Socket Head Cap Screw 005-SH870
2 8mm Flat Washer 005-WF8
2 26mm Aluminum Spacer 005-S-26
2 Barrel Clamps 005-27-61MSH
1 Permatex Ultra Black Gasket Maker 031-P22072
IMPORTANT - PLEASE READ CAREFULLY
Warranty
two brothers racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. two brothers racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the
use of these products or parts.
We recommend that this performance part be installed by a qualified
technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer.
Read all instructions first before starting installation. Make sure the
motorcycle and exhaust system are completely cool before starting the
installation. Also, make sure the bike is secure on a centerstand or ideally
a service lift during installation. Be sure to save all stock components for
possible use later.
Suzuki
DL1000 V-STROM
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is
completely cool before maintenance.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the
bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always
apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply
cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside
is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include
everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the
intense heat and lack of cooling air can quickly burn through the canister material. Two
Brothers Racing does not provide a warranty for burned canisters.
Muffler Inlet
X-Lite™ Ring
Slip Tube
V.A.L.E.™ Assembly Detail