Two Brothers Racing Honda VFR750 - Manual

Parts List
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions first before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Also,
make sure the bike is secure on a center stand or ideally a service lift during
installation. Be sure to save all stock components for possible use later.
Installation Instructions
1. Make sure the bike is completely cool before starting the installation. Make sure the bike is secure on the sidestand or
ideally a rear service stand.
2. Loosen the clamp that holds the canister to the headers under the bike. Remove the hardware that holds the stock canister
at the passenger footpeg bracket. Take off the canister. Be careful to avoid damaging the round gasket, you’ll need to use it
again.
3. Install the new S-bend pipe onto the end of the header collector, reusing the stock gasket and clamp. Leave loose for now.
4. Instal VALE adapter kit using the supplied kit instructions.
5. Place a bead of the hi-temp sealant on the outside edge of the s-bend that goes into the canister. Slide the canister onto
the end of the S-bend pipe. Wipe off the excess sealant that will squeeze out.
6. Carefully slide the canister clamp over the canister. (Note: The stainless steel canister clamp and the name badge on the
canister come from the factory with a clear plastic protective film. Please remove this film before operation.) You may need
to twist and turn the S-bend a little to get it in the right place. Locate both tabs of the canister clamp on the inside of the
passenger footpeg bracket. Use the stock hardware to secure it. Leave loose for now.
7. Make sure everything is aligned and tighten all hardware. Affix the connector springs to the muffler.
8. Be sure to allow the sealant to dry per the manufacturer’s instructions before starting the bike. Before you run the bike,
clean off all fingerprints and dirt, as any oily residue will etch the metal and become somewhat permanent when the
system gets hot. Run the bike and enjoy. It is normal for some white smoke to appear the first time you start the bike.
This is packing/manufacturing oil from inside the pipe burning off. Check for gaps or leaks. If you find a leak, a little high
temperature silicon sealant should fix it. After 50 to 100 miles, recheck all fasteners for tightness.
1994-97 Honda
VFR750
V.A.L.E.™ Slip-on Exhaust System with M-2 Canister
Part # 005-360406M, 005-360407M, 005-360408M
Qty. Description Part Number
1 Muffler Canister Varies
1 Canister Clamp Varies
1 Stainless Steel S-Bend Tube 005-36-10604
1 HARDWARE KIT 005-36-3
1 VALE Adapter Kit 005-2-1-V
2 80mm Swivel Hook Spring 005-S80
1 Permatex Ultra Black Gasket Maker 031-P22072
1 T20 Torx Screw Wrench 005-9-15820
1 TBR Sticker Kit 015-10212
V.A.L.E.
V a r i a b l e a x i s l o c k i n g e x h a u s t
TM
Care & Cleaning
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. For cleaning use a mild spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality
stainless steel.
Carbon Fiber Mufflers: Always make sure the fiberglass packing inside is in good condition and not burned out, as exhaust heat inside an empty canister will
deteriorate the Carbon Fiber sleeve. TBR sells repack kits (TBR part # 005-10038) that include new rivets and repack material as well as a drill bit (#30), making
it easy to do yourself. Also, NEVER dyno test your bike with carbon fiber mufflers installed - the intense heat and lack of cooling air can quickly cause the CF
material to burn. Two Brothers Racing does not provide a warranty for burned carbon fiber.
Aluminum Mufflers: Use an aluminum or mag wheel polish such as Mother’s to restore the bright finish to factory spec.
Repack all road canisters every 3,000 miles. Part #005-10038
Warranty
two brothers racing products are intended for closed course competition purposes only, and therefore are sold “as is” without warranty. two brothers racing specifically disclaims any
warranties of merchantability or fitness for a particular purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use of these
products or parts.