Ddetail d scale 1 : 7, Wdetail w scale 1 : 7, Device configuration recommendations – Amico Light-Duty Monitor Arm User Manual
Page 12: Figure 6, Warning, Figure 4 figure 5 figure 6, Project 394, Lma-__-(_____)
12
Amico Accessories Inc.
SECTION 4: Device Installation
Device Configuration Recommendations
1. Determine the monitor configuration and if spacers are required. The monitor configuration will be either VESA
75 (75 mm x 75 mm M4 thread) or VESA 100 (100 mm x 100 mm M4 threads).
2. For VESA 100 configuration: two M4 screws are partially threaded into the top two holes at the back of the
monitor. The monitor can then be hung up on the X-FIT-VSA-PLT through the two slots at the top. Insert two
more screws through the X-FIT-VSA-PLT 100 mounting holes at the bottom and tighten all screws (Figure 4).
3. For VESA-75 configuration: Rotate X-FIT-VSA-PLT so the two slots for the VESA-75 configuration are located at the
top (
Figure 6
). Partially thread two screws into the top two holes at the back of the monitor. The monitor can
then be hung up on the VESA head through the two slots at the top. Insert two more screws through the VESA-
75 mounting holes at the bottom and tighten all screws (Figure 4).
WARNING
When removing the monitor, the monitor arm and the monitor should be placed at the highest
position. Remove the two bottom screws from the VESA plate, loosen the top two screws and then lift the
monitor off the VESA plate.
4. If spacers are required, for both VESA 75 and VESA 100 monitor configurations, place the monitor down on a
protective surface. Align and tighten four longer M4 screws through X-FIT-VSA-PLT and spacers into monitor
(Figure 5).
D
DETAIL D
SCALE 1 : 7
MONITOR
(NOT PROVIDED)
4 X M4 screws
(PART OF X-LMA-01/02-01)
LMA-__-(_____)-__
W
DETAIL W
SCALE 1 : 7
LMA-__-(_____)-__
MONITOR
(NOT PROVIDED)
X-FIT-VSA-PLT
(PART OF LMA-__-(_____)-__
4 X Longer M4 screws
(PART OF X-LMA-01/02-01)
4 X spacers
(PART OF X-LMA-01/02-01)
CUSTOMER
FOR USE WITH: LMA-__-(_____)-__
Determine the monitor configuration. VESA 75 (75 mm x 75 mm M4 thread) or VESA 100 (100 mm x 100 mm M4 threads) and if spacers are required.
1.
VESA 100 configuration: 2 x M4 screws are partially threaded into the top 2 holes at the back of the monitor. The monitor can then be hung up
2.
on the X-FIT-VSA-PLT through the two slots at the top. Insert 2 more screws through the X-FIT-VSA-PLT 100 mounting holes at the bottom
and tighten all screws. (Figure 1)
VESA-75 configuration: Rotate X-FIT-VSA-PLT so the 2 slots for the VESA-75 configuration are located at the top. (Figure 3) Partially thread two screws
3.
into the top 2 holes at the back of the monitor. The monitor can then be hung up on the VESA Head through the two slots at the top. Insert 2
more screws through the VESA-75 mounting holes at the bottom and tighten all screws. (Figure 1)
When removing the monitor, the monitor arm and the monitor should be placed at the highest position. Remove the 2 bottom screws
4.
from the VESA plate, loosen the top 2 screws, and lift the monitor off the VESA plate.
If spacers are required, for both VESA 75 and VESA 100 monitor configurations, place the monitor down on a protective surface. Align and tighten
5.
4x Longer M4 screws through X-FIT-VSA-PLT and spacers into monitor. (Figure 2)
PROJECT 394
Holes for VESA 100 pattern
Holes for VESA 75 pattern
5
4
3 2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
4
11
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
LMA ASSEMBLY
JT
2014-05-26
EC
2014-06-10
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: (905) 763.7778
Fax: (905) 763.8587
LMA ASSEMBLY
LMA-__-(_____)-__
20140526-E2900
PROJECTION
www.amico.com
D
DETAIL D
SCALE 1 : 7
MONITOR
(NOT PROVIDED)
4 X M4 screws
(PART OF X-LMA-01/02-01)
LMA-__-(_____)-__
W
DETAIL W
SCALE 1 : 7
LMA-__-(_____)-__
MONITOR
(NOT PROVIDED)
X-FIT-VSA-PLT
(PART OF LMA-__-(_____)-__
4 X Longer M4 screws
(PART OF X-LMA-01/02-01)
4 X spacers
(PART OF X-LMA-01/02-01)
CUSTOMER
FOR USE WITH: LMA-__-(_____)-__
Determine the monitor configuration. VESA 75 (75 mm x 75 mm M4 thread) or VESA 100 (100 mm x 100 mm M4 threads) and if spacers are required.
1.
VESA 100 configuration: 2 x M4 screws are partially threaded into the top 2 holes at the back of the monitor. The monitor can then be hung up
2.
on the X-FIT-VSA-PLT through the two slots at the top. Insert 2 more screws through the X-FIT-VSA-PLT 100 mounting holes at the bottom
and tighten all screws. (Figure 1)
VESA-75 configuration: Rotate X-FIT-VSA-PLT so the 2 slots for the VESA-75 configuration are located at the top. (Figure 3) Partially thread two screws
3.
into the top 2 holes at the back of the monitor. The monitor can then be hung up on the VESA Head through the two slots at the top. Insert 2
more screws through the VESA-75 mounting holes at the bottom and tighten all screws. (Figure 1)
When removing the monitor, the monitor arm and the monitor should be placed at the highest position. Remove the 2 bottom screws
4.
from the VESA plate, loosen the top 2 screws, and lift the monitor off the VESA plate.
If spacers are required, for both VESA 75 and VESA 100 monitor configurations, place the monitor down on a protective surface. Align and tighten
5.
4x Longer M4 screws through X-FIT-VSA-PLT and spacers into monitor. (Figure 2)
PROJECT 394
Holes for VESA 100 pattern
Holes for VESA 75 pattern
5
4
3 2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
4
11
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
LMA ASSEMBLY
JT
2014-05-26
EC
2014-06-10
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: (905) 763.7778
Fax: (905) 763.8587
LMA ASSEMBLY
LMA-__-(_____)-__
20140526-E2900
PROJECTION
www.amico.com
D
DETAIL D
SCALE 1 : 7
MONITOR
(NOT PROVIDED)
4 X M4 screws
(PART OF X-LMA-01/02-01)
LMA-__-(_____)-__
W
DETAIL W
SCALE 1 : 7
LMA-__-(_____)-__
MONITOR
(NOT PROVIDED)
X-FIT-VSA-PLT
(PART OF LMA-__-(_____)-__
4 X Longer M4 screws
(PART OF X-LMA-01/02-01)
4 X spacers
(PART OF X-LMA-01/02-01)
CUSTOMER
FOR USE WITH: LMA-__-(_____)-__
Determine the monitor configuration. VESA 75 (75 mm x 75 mm M4 thread) or VESA 100 (100 mm x 100 mm M4 threads) and if spacers are required.
1.
VESA 100 configuration: 2 x M4 screws are partially threaded into the top 2 holes at the back of the monitor. The monitor can then be hung up
2.
on the X-FIT-VSA-PLT through the two slots at the top. Insert 2 more screws through the X-FIT-VSA-PLT 100 mounting holes at the bottom
and tighten all screws. (Figure 1)
VESA-75 configuration: Rotate X-FIT-VSA-PLT so the 2 slots for the VESA-75 configuration are located at the top. (Figure 3) Partially thread two screws
3.
into the top 2 holes at the back of the monitor. The monitor can then be hung up on the VESA Head through the two slots at the top. Insert 2
more screws through the VESA-75 mounting holes at the bottom and tighten all screws. (Figure 1)
When removing the monitor, the monitor arm and the monitor should be placed at the highest position. Remove the 2 bottom screws
4.
from the VESA plate, loosen the top 2 screws, and lift the monitor off the VESA plate.
If spacers are required, for both VESA 75 and VESA 100 monitor configurations, place the monitor down on a protective surface. Align and tighten
5.
4x Longer M4 screws through X-FIT-VSA-PLT and spacers into monitor. (Figure 2)
PROJECT 394
Holes for VESA 100 pattern
Holes for VESA 75 pattern
5
4
3 2
1
DESCRIPTION:
PART NO:
SCALE:
DRAWN BY:
CHECKED BY:
SHT.
OF
DRAWING NO:
NTS
4
11
PRIVATE AND CONFIDENTIAL
THIS PRINT IS PROPERTY OF AMICO ACCESSORIES
AND IS LOANED IN CONFIDENCE SUBJECT TO RETURN
UPON REQUEST AND WITH THE UNDERSTANDING THAT
NO COPIES ARE TO BE MADE WITHOUT THE CONSENT
OF AMICO ACCESSORIES
ALL RIGHTS TO DESIGN OR INVENTION ARE RESERVED
DATE:
DATE:
LMA ASSEMBLY
JT
2014-05-26
EC
2014-06-10
85 Fulton Way
Richmond Hill, Ontario
L4B 2N4, Canada
Toll Free: 1.877.264.2697 (T)
Tel: (905) 763.7778
Fax: (905) 763.8587
LMA ASSEMBLY
LMA-__-(_____)-__
20140526-E2900
PROJECTION
www.amico.com
Figure 4
Figure 5
Figure 6