Tweco 12mm Cutmaster User Manual

10mm 12mm cutmaster, Operating manual, Plasma cutting system

Art A-10399

AMP

PHASE

240

PLASMA CUTTING SYSTEM

10mm

12mm CUTMASTER

™

Rev. AE

Date: September 3, 2012

Manual # 0-5197AE

Operating Features:

Operating Manual

This manual is related to the following products:

10mm Cutmaster

Table of contents

Document Outline

0-5178-CCR
SECTION 1:GENERAL INFORMATION
- 1.01 Notes, Cautions and Warnings
- 1.02 Important Safety Precautions
- 1.03 Publications
- 1.04 Declaration of Conformity
SECTION 2 SYSTEM:INTRODUCTION
- 2.01 How To Use This Manual
- 2.02 Equipment Identification
- 2.03 Receipt Of Equipment
- 2.04 Working Principle
- 2.05 Power Source Specifications
- 2.06 Input Wiring Specifications
- 2.07 Power Source Feature Locations
SECTION 2 TORCH:INTRODUCTION
- 2T.01 Scope of Operating Manual
- 2T.02 Specifications
- 2T.03 Introduction to Plasma
SECTION 3:INSTALLATION
- 3.01 Unpacking
- 3.02 Lifting Options
- 3.03 Air Supply Connections
SECTION 4 SYSTEM:OPERATION
- 4.01 Control Panel
- 4.02 Preparations for Operating
- 4.03 Sequence of Operation
- 4.04 Cut Quality
- 4.05 General Cutting Information
SECTION 5 SYSTEM: SERVICE
- 5.01 General Maintenance
- 5.02 Basic Troubleshooting Guide
SECTION 5 TORCH:SERVICE
- 5T.01 General Maintenance
- 5T.02 Inspection and Replacement of Consumable Torch Parts
SECTION 6:PARTS LIST
- 6.01 Introduction
- 6.02 Power Source Replacement Parts
- 6.03 SL60 Replacement Parts
- 6.04 Options and Accessories
APPENDIX 1:CIRCUIT DIAGRAM
Statement of Warranty
GLOBAL CUSTOMER SERVICE CONTACT INFORMATION
SECTION 1:GENERAL INFORMATION
- Table 1-1 - Protective Filters
SECTION 2 SYSTEM:INTRODUCTION
- Figure 2-1 - Power Source Dimensions & Weight
- Figure 2-2 - Power Source Setup
- Figure 2-3 - Power Source Rear View
SECTION 2 TORCH:INTRODUCTION
- Figure 2T-1 - SL60 Torch
- Figure 2T-2 - Typical Torch Head Detail
- Figure 2T-3 - Parts-in-Place Circuit Diagram for Hand Torch
SECTION 3:INSTALLATION
- Figure 3-1 - Gas Connection to Compressed Air Input
- Figure 3-2 - Optional Single - Stage Filter Installation for Compressed Air Input
SECTION 4 SYSTEM:OPERATION
- Figure 4-1 - Front Control Panel
- Figure 4-2 - Rear Controls
- Figure 4-3 - SL60 Torch Parts
- Figure 4-4 - Work Cable Connection
- Figure 4-5 - Rear Panel with ON/OFF Switch
- Figure 4-6 - Front Panel with Power ON/OFF Indicator
- Figure 4-7 - Torch Trigger Release
- Figure 4-8 - Standoff Distance
- Figure 4-9 - Standoff Cutting
- Figure 4-10 - Torch Trigger Release
- Figure 4-11 - Drag Cutting
- Figure 4-12 - Cut Quality Characteristics
- Figure 4-13 - Side Characteristics of Cut
SECTION 5 TORCH:SERVICE
- Figure 5-1 - Torch Head O-Ring
- Figure 5-2 - ATC O-Ring
- Figure 5-3 - Consumable Parts
- Figure 5-4 - Tip Wear
- Figure 5-5 - Start Cartridge
- Figure 5-6 - Electrode Wear
SECTION 6:PARTS LIST
- Parts 6-1 - Power Source
- Parts 6-2 - Electrode Parts
APPENDIX 1:CIRCUIT DIAGRAM
SECTION 1: GENERAL INFORMATION
- 1.01 Notes, Cautions and Warnings
SECTION 2 SYSTEM: INTRODUCTION
- 2.01 Working Principle
- 2.02 Power Supply Specifications
SECTION 2TORCH: INTRODUCTION
- 2T.01 Scope of Manual
- 2T.02 Specifications
- 2T.03 Introduction to Plasma
SECTION 3: INSTALLATION
- 3.01 Unpacking
- 3.02 Lifting Options
SECTION 4 SYSTEM: OPERATION
- 4.01 Control Panel
- 4.02 Preparations For Operating
- 4.03 Sequence of Operation
- 4.04 Cut Quality
- 4.05 General Cutting Information
SECTION 5 SYSTEM: SERVICE
- 5.01 General Maintenance
- 5.02 Basic Troubleshooting Guide
SECTION 5 TORCH: SERVICE
- 5T.02 Inspection and Replacement of Consumable Torch Parts
SECTION 6: PARTS LISTS
- 6.01 Introduction
- 6.02 Power Supply Replacement Parts
APPENDIX 1: CIRCUIT DIAGRAM
0-5178-Rear