Watts KA2-A - Manual (Page 2)

6. Remove the screen and the O-ring from the inlet fi t-
tings. (See Figure 3).
7. Using the O-ring grease provided, lubricate and install
the two new O-rings “B” (See Figure 4) provided onto
the adapter sleeve (E) (See Figure 5).
8. Insert adapter sleeve with O-rings installed into the
valve body inlet (J).
9. Thread the adapter body (D) onto the A2-M1 valve
body inlet (J). (Note: Be careful not to cross-thread
the adapter). Thread to a positive stop, then orient the
adapter such that the smaller opening faces forward
when looking directly at the A2-M1 valve.
10. Lubricate and install O-ring “A” on the angle adapter
(F).
11. Lubricate and install O-ring “C” on the stainless steel
screw (G).
12. P l a c e t h e a d a p t e r b o d y ( D ) o n t o t h e a n g l e
adapters (F) and install screw (G) to retain the adapt-
er, tighten fi rmly.
13. Refer to the A2C-M1 product installation instruc-
tions to complete the installation and perform a fi nal
check.
Figure 3
Figure 4
Adapter Sleeve
(E)
“A” “B” “C”
Screen
Figure 6
O-Ring “B”
Adapter Body
(D)
O-Ring “C”
Stainless Steel
Screw (G)
O-Ring “B”
O-Ring “A”
Angle
Adapter
(F)
Valve Body
Inlet (J)
IS-KA2-A 0829 EDP# 1911451 © Watts, 2008
USA: 815 Chestnut St., No. Andover, MA 01845-6098; www.watts.com
Canada: 5435 North Service Rd., Burlington, ONT. L7L 5H7; www.wattscanada.ca
W a t e r S a f e t y & F l o w C o n t r o l P r o d u c t s
Limited Warranty: Watts Regulator Co. (the “Company”) warrants each product to be free from defects in material and work-
manship under normal usage for a period of one year from the date of original shipment. In the event of such defects within
the warranty period, the Company will, at its option, replace or recondition the product without charge.
THE WARRANTY SET FORTH HEREIN IS GIVEN EXPRESSLY AND IS THE ONLY WARRANTY GIVEN BY THE COMPANY WITH
RESPECT TO THE PRODUCT. THE COMPANY MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE COMPANY
HEREBY SPECIFICALLY DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO
THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
The remedy described in the first paragraph of this warranty shall constitute the sole and exclusive remedy for breach of
warranty, and the Company shall not be responsible for any incidental, special or consequential damages, including without
limitation, lost profits or the cost of repairing or replacing other property which is damaged if this product does not work prop-
erly, other costs resulting from labor charges, delays, vandalism, negligence, fouling caused by foreign material, damage from
adverse water conditions, chemical, or any other circumstances over which the Company has no control. This warranty shall be
invalidated by any abuse, misuse, misapplication, improper installation or improper maintenance or alteration of the product.
Some States do not allow limitations on how long an implied warranty lasts, and some States do not allow the exclusion or
limitation of incidental or consequential damages. Therefore the above limitations may not apply to you. This Limited Warranty
gives you specific legal rights, and you may have other rights that vary from State to State. You should consult applicable state
laws to determine your rights. SO FAR AS IS CONSISTENT WITH APPLICABLE STATE LAW, ANY IMPLIED WARRANTIES
THAT MAY NOT BE DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL SHIPMENT.
Figure 5
IS-KA2-A.indd 2 9/12/08 2:40:43 PM