Banner K50 Pick-to-Light EZ-LIGHT - Manual (Page 2)

Specialty C-Series – Two Color, 12-30V dc
• Job light is ON at all times while job input is active.
• Presence of hand (or pressing push button) activates output.
Model Sensing Mode / LED Range Cable* Output Job Light
K50RPLPGRCQ Visible red, 680 nm 2 m (6 ft) 4-pin Euro QD PNP (Sourcing) Green (Red)
NPN (Sinking) K50RNLPGRCQ
K50APFF50GRCQ Infrared, 880 nm 50 mm cutoff PNP (Sourcing)
K50ANFF50GRCQ NPN (Sinking)
K50APFF100GRCQ 100 mm cutoff PNP (Sourcing)
K50ANFF100GRCQ NPN (Sinking)
K50APPBGRCQ Push button — PNP (Sourcing)
K50ANPBGRCQ NPN (Sinking)
* Only 4-pin integral Euro-style QD models are listed. For 2 m (6 ft) PVC cable model, omit suffix “Q” from model number (e.g., K50APLPGRCQP).
For 9 m (30 ft) PVC cable model, replace suffix “Q” with “W/30” (e.g., “K50APLPGRC W/30”).
For 150 mm (5.9 in) PVC pigtail with 5-pin Euro-style fitting, replace suffix “Q” with “QP” (e.g., K50RPLPGRCQP).
A model with a QD requires a mating cordset.
C-Series 2-Color Models
• Job light is Green at all times while job input is active.
• Presence of hand (or pressing push button) activates output.
• Presence of hand (or pressing push button) while job input is inactive causes unit to light Red, for visual verification that sensor is functioning properly.
Model Sensing Mode / LED Range Cable* Output Job Light
K50RPLPGREQ Polarized retroreflective, visible red,
680 nm 2 m (6 ft) Integral 4-pin Eu-
ro QD PNP (Sourcing) Green (Red)
NPN (Sinking) K50RNLPGREQ
K50APFF50GREQ Fixed field infrared, 880 nm 50 mm cutoff PNP (Sourcing)
K50ANFF50GREQ NPN (Sinking)
K50APFF100GREQ 100 mm cutoff PNP (Sourcing)
K50ANFF100GREQ NPN (Sinking)
K50APPBGREQ Push button — PNP (Sourcing)
K50ANPBGREQ NPN (Sinking)
* Only 4-pin integral Euro-style QD models are listed. For 2 m (6 ft) PVC cable model, omit suffix “Q” from model number (e.g., K50RPLPGRE).
For 9 m (30 ft) PVC cable model, replace suffix “Q” with “W/30” (e.g., K50RPLPGRE W/30).
For 150 mm (5.9 in) PVC pigtail with 4-pin Euro-style fitting, replace suffix “Q” with “QP” (e.g., K50RPLPGREQP).
A model with a QD requires a mating cordset.
Installation
For push-button models, install the sensor at such a height and in a location that will be easy for the user and/or supervisor to see the indicator and will be comfortable for
the user to press the push-button.
For other models, install the sensor in a location that will be comfortable for the user to break the beam when reaching for the required part. When multiple sensors will be
located in close proximity, to monitor multiple bins for example, mount all the sensors in a similar sensing position (all mounted at the tops of the bins and pointing down, for
example). This may reduce potential optical crosstalk, where one sensor detects another sensor’s beam.
K50 Series Pick-to-Light
2 www.bannerengineering.com - tel: 763-544-3164 P/N 125680 Rev. C