Banner SPS101 DC Sensor Power Supply - Manual (Page 2)

SPS101 DC Sensor Power Supply
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: [email protected]
Style Model Length
5-Pin
Mini-Style
Straight
MBCC-506
MBCC-512
MBCC-530 2 m (6.5')
4 m (12')
9 m (30')
Pin-Out (Female View)
WARRANTY: Banner Engineering Corp.
warrants its products to be free from defects
for one year. Banner Engineering Corp. will
repair or replace, free of charge, any product
of its manufacture found to be defective at
the time it is returned to the factory during
the warranty period. This warranty does not
cover damage or liability for the improper
application of Banner products. This
warranty is in lieu of any other warranty
either expressed or implied.
Quick-Disconnect Cables
SPS101 Sensor Power Supply Specifications
Output Power 120mA maximum: 12V dc minimum, 30V dc maximum (dependent on load)
Output Configuration SPS101Q(P) models: “Form A” (SPST) electromechanical relay
SPS101SQ(P) models: Optically isolated SPST solid-state switch
Output Rating
NOTE: Output of the solid-
state models is not
short-circuit
protected. Exercise
care when making
wiring connections.
SPS101Q(P) models
Max. switching power (resistive load): 150 W, 600 VA
Max. switching voltage (resistive load): 250V ac or 30V dc (120V ac max. per UL & CSA)
Max. switching current (resistive load): 5A
Min. voltage and current: 1 amp at 5V dc, 0.1 amp at 24V dc
Peak switching voltage: 750V ac (transient suppression recommended)
Mechanical life of relay: 10,000,000 operations
SPS101SQ(P) models
Max. switching voltage: 250V ac or 250V dc
Max. switching current: 300 mA
On-state saturation voltage: less than 3V at 300 mA; less than 2V at 15 mA
Off-state leakage current: < 50 microamps
Inrush current: 1 amp for 20 milliseconds, non-repetitive
Connections Power connector: 5-pin Mini-style quick disconnect
Sensor connector:
“Q” version: 5-pin Euro-style quick-disconnect mounted on housing
“QP” version: Shielded, PVC jacketed 5-pin pigtail Euro-style quick-disconnect, 0.5 meter long
Environmental Rating IEC IP54
Operating Conditions Temperature: -20° to +50°C (-4° to 122°F)
Maximum Relative Humidity: 90% @ +50°C (non-condensing)
Additional Notes Compatible with Banner dc sensors with NPN or PNP output, equipped with 4- or 5-pin Euro-style quick-
disconnect (except NAMUR sensors). Minimum of 630V isolation from earth ground to dc output of circuit.
Supply Voltage 105V ac to 130V ac, 60Hz
Status Indicators Power On (green) and Output On (red)
pin 4
pin 2
105-
130V ac
pin 1
pin 5
pin 3
pin 1
pin 3
pin 2
pin 4
pin 5
Relay
Output
DC
Voltage
Sensor Output (NPN or PNP)
No Connection
No Connection
+
–
GND
(Earth Ground)
Mini-Style Connector
Euro-Style Connector
(to DC Sensor)
AC to DC
Voltage
Converter
Output
Drive
Circuit
SPS101 Sensor Power Supply Hookups
5
4
3
2
1
White
Brown
Yellow
Blue
Black
10
15
20
25
20 0 40
Output Current Draw (milliamps)
Voltage Regulation vs. Load
Output V
o
ltage (V dc)
60 80 100
105V ac Input
115V ac Input
130V ac Input