beautypg.com

Q25 sensors – ac-voltage series, Banner engineering corp limited warranty, Specifications – Banner Q25 Series User Manual

Page 2: Quick-disconnect (qd) cables

background image

Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: [email protected]

Q25 Sensors – ac-Voltage Series

P/N 116166 rev. B

Supply Voltage and Current

20 to 250V ac (50/60 Hz). Average current: 20 mA

Peak current: 200 mA at 20V ac, 500 mA at 120V ac, 750 mA at 250V ac

Supply Protection Circuitry

Protected against transient voltages

Output Configuration

SPST solid-state ac switch; Three-wire hookup; Choose light operate or dark

operate models

Light Operate: Output conducts when sensor sees its own (or the emitter’s)

modulated light

Dark Operate: Output conducts when the sensor sees dark

Output Rating
300 mA maximum (continuous);

Fixed-Field Models: derate 5 mA/°C above +50°C (+122°F)

Inrush Capability 1 amp for 20 milliseconds, non-repetitive

OFF-state leakage current: < 100 microamps

ON-state saturation voltage: 3V at 300 mA ac; 2V at 15 mA ac

Output Protection Circuitry

Protected against false pulse on power-up

Output Response Time
Opposed Mode:
16 milliseconds ON, 8 milliseconds OFF
Other Models: 16 milliseconds ON and OFF

NOTE: 100 millisecond delay on power-up

Repeatability
Opposed Mode:
2 milliseconds
Other Models: 4 milliseconds
Repeatability and response are independent of signal strength.
Indicators

Two LEDs (Green and Yellow)

Green ON steady: power to sensor is ON

Yellow ON steady: sensor sees light

Yellow flashing: excess gain marginal (1 to 1.5x) in light condition

Construction

PBT polyester housing; polycarbonate (opposed-mode) or acrylic lens

Environmental Rating

Leakproof design rated NEMA 6P, DIN 40050 (IP69K)

Connections

2 m (6.5') attached cable, or 4-pin Micro-style quick-disconnect fitting

Operating Conditions
Temperature:
-40° to +70°C (-40° to +158°F);

Maximum relative humidity: 90% at 50°C (non-condensing)
Vibration and Mechanical Shock

All models meet Mil. Std. 202F requirements. Method 201A (Vibration;

frequency 10 to 60 Hz, max., double amplitude 0.06" acceleration 10G).

Method 213B conditions H&I (Shock: 75G with unit operating; 100G for

non-operation)

Certifications

LISTED

R

Specifications

Style

Model

Length

Dimensions

Pinout

4-pin

Micro-style

Straight

MQAC-406

MQAC-415

MQAC-430

2 m (6.5')

5 m (15')

9 m (30')

4-pin

Micro-style

Right-angle

MQAC-406RA

MQAC-415RA

MQAC-430RA

2 m (6.5')

5 m (15')

9 m (30')

Quick-Disconnect (QD) Cables

��������������

������

������

����������

������

38 mm max.

(1.5")

1/2-20UNF-2B

ø 15 mm

(0.6")

38 mm max.

(1.5")

Green Wire

Red/Black

Wire

Red/White

Wire

Red Wire

Banner Engineering Corp Limited Warranty

Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engin-

eering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective

during the warranty period.This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the Banner product.
THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (INCLUDING, WITHOUT LIM-

ITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF

PERFORMANCE, COURSE OF DEALING OR TRADE USAGE.
This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING

CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR ANY

INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE

PRODUCT, WHETHER ARISING IN CONTRACT OR WARRANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE.

Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any

product previously manufactured by Banner Engineering Corp.