Bang & Olufsen BeoVision Avant CTV (1995-2005) - User Guide - Manual (Page 11)

11
What’s on the first TV tuning menu…
Freq (frequency)... Searching stops at the first
station producing an acceptable signal. If you
know a station’s exact frequency number, key it in
directly using the number buttons.
(System)… If System appears on the menu, make
sure that the correct broadcast system is displayed
before you start tuning:
B/G...
for PAL/SECAM B/G
I... for PAL I
L... for SECAM L
M... for NTSC
D/K... for PAL/SECAM D/K
Note: All options may not be available as this
depends on the television type.
Pr (program number)... Key in the program
number (1-99) you wish to preset the station on.
Name (naming)... The name you give a station
will appear in the TV program list.
Press ▲ or ▼ to reveal the character you want.
Press 0 to switch from upper to lower case, or vice
versa. Then press
tt to move on to the next
character position.
Then press GO or move on to More... When
you have entered the information you want, press
GO to store your TV program or….
More… If it is necessary to fill in extra
information, move to More and press GO. A
second TV tuning menu appears for fine tuning,
availability of decoder and type of sound or
format.
What’s on the second TV tuning menu…
Fine (fine tuning)... The TV automatically tunes to
the best possible picture. However, neighbouring
channels may blur the picture slightly, in which
case fine tuning may be required. You fine tune
by 8 steps above or below the standard frequency.
(Decoder)… Only appears if you have selected
Decoder or Auto in the Sources menu. If you tune
in a coded TV station and want the decoder to be
cut in automatically, set the item Decoder to one
of the On options below:
ON/AV...
(decoder on) where both audio and
video signals are coded
ON/V... (decoder on) where only video
signals are coded
OFF... (decoder off) for no decoder
Select ON/AV for most coded programs to get
both sound and pictures. If only the video signal is
coded, select ON/V. If you select ON/AV where
only the video signal is coded, the sound may be
lost when the signal is decoded.
Note: If an extra decoder is connected to the
BeoVision Avant AV socket and Decoder-2 is
entered into the AV Source menu ( see page 36,
Extra video equipment), you can choose between
1/AV or 1/V, for decoder-1, and 2/AV or 2/V for
decoder-2 or OFF for no decoder.
Sound (mono/stereo/language)... Several types of
sound may available for a TV station, for example
both stereo and mono sound, or several different
languages. Press
▲ or ▼ to switch between the
sound modes currently transmitted, when the
sound you wish to store is heard/displayed, press
GO.
Note: Even though you store a type of sound/
language in this way, you can still switch between
the various types of sound while you are watching
this TV station.
Press LIST to display SOUND* on the Beo4 remote
control, then press GO repeatedly to switch
sound. See page 33, Switching sound for more
information about the various types of sound
available.
*Note: In order to display SOUND on Beo4, you
must add the function to the Beo4 LIST function,
see Extra functions in Beo4, page 49.
Format... Two format settings are available, you
can store a format for each TV program. The
default setting is 15:9, but if ”noise” appears in
the right and left side of the picture, choose the
14:9 format instead, enabling the curtains on the
TV screen to hide the ”noise”. You can still
change the picture format for each program even
though you have stored a setting, see page 38-39.
Removing a tuned TV station…
Press MENU to call up the main menu, press 2
to call up the TV program list, use the
▲ and ▼
buttons to move the cursor to the station you
want to remove. Then press MENU. When
Del? appears, press GO to delete the program.
See Program list, page 23, for further
information.