Sportsliter Solutions Remote System - Manual (Page 9)

REMOTE SYSTEM
INSTALLATION
8
CAP PLATE COMPONENT MOUNTING TO STEEL OR CONCRETE POLES (FIG. 11)
ATTACH WIRING HARNESS STRAIN
RELIF TO SUPPORT INSIDE
CROSSARM ASSEMBLY
CROSSARM MOUNTING HARDWARE
SHIPPED WITH CROSSARM ASSEMBLY
¾” O BOLT (4)
FLAT WASHERS
NUT LOCK
WASHER
CROSSARM MTG. DETAIL
NOTE: TIGHTEN NUTS ON MTG. DETAIL
TO 100 ft/lbs. MINIMUM
CROSSARM ASSEMBLY
FIELD SIDE
HANDHOLE
WIRING HARNESS
CONNECT TO PLUG IN
REMOTE BALLAST BOX
AND JUNCTION BOX AT
TOP
SEAL ANY OPENINGS AROUND
BOTTOM ATTACHMENT POINT
WITH SILICONE SEALANT
SUPPLY WIRING
(BY OTHERS)
REMOTE BALLAST BOX
SECURE TO POLE WITH
¾” O BOLTS (2) AND
WASHERS SHIPPED WITH
BOX. (TIGHTEN TO 20 ft/lbs.
MAX)
STEEL OR CONCRETE POLE
GASKET BETWEEN POLE & REMOTE
BALLAST BOX FOR WATERTHGHT SEAL
FOR DETAILED INSTALLATION INSTRUCTIONS
FOR THE REMOTE BAX, SEE THE INSTRUCTION
SHEET INCLUDED WITH EACH.
CAP PLATE COMPONENT MOUNTING TO STEEL OR CONCRETE POLES (FIG. 11)
ATTACH WIRING HARNESS STRAIN
RELIF TO SUPPORT INSIDE
CROSSARM ASSEMBLY
CROSSARM MOUNTING HARDWARE
SHIPPED WITH CROSSARM ASSEMBLY
¾” O BOLT (4)
FLAT WASHERS
NUT LOCK
WASHER
CROSSARM MTG. DETAIL
NOTE: TIGHTEN NUTS ON MTG. DETAIL
TO 100 ft/lbs. MINIMUM
CROSSARM ASSEMBLY
FIELD SIDE
HANDHOLE
WIRING HARNESS
CONNECT TO PLUG IN
REMOTE BALLAST BOX
AND JUNCTION BOX AT
TOP
SEAL ANY OPENINGS AROUND
BOTTOM ATTACHMENT POINT
WITH SILICONE SEALANT
SUPPLY WIRING
(BY OTHERS)
REMOTE BALLAST BOX
SECURE TO POLE WITH
¾” O BOLTS (2) AND
WASHERS SHIPPED WITH
BOX. (TIGHTEN TO 20 ft/lbs.
MAX)
STEEL OR CONCRETE POLE
GASKET BETWEEN POLE & REMOTE
BALLAST BOX FOR WATERTHGHT SEAL
FOR DETAILED INSTALLATION INSTRUCTIONS
FOR THE REMOTE BAX, SEE THE INSTRUCTION
SHEET INCLUDED WITH EACH.
REMOTE HEAD POSITIONING AND REFLECTOR MTG. INSTRUCTIONS (FIG. 12)
CROSSARM ASSEMBLY
AIMING BRACKET
SPRING-LOADED
RETAINING PIN
REMOTE HEAD
HEAD BOLT
SHIPPED POSITION
FIELD POSITION
(PRE-AIMED AT FACTORY)
GASKET
LAMP SUPPORT BKT.
(AXIAL OPTICS)
•REMOVE THE PLASTIC PROTECTIVE WRAP FROM THE
REMOTE HEAD.
•REMOVE THE LAMP SUPPORT BRACKET FROM THE
REMOTE HEAD (AXIAL OPTICS).
•LOOSEN THE HEAD BOLT NUT.
•SWING THE REMOTE HEAD UP UNTIL THE SPRING-
LOADED RETAINING PIN ENGAGES THE HOLE IN
THE AIMING BRACKET.
•RE-TIGHTEN THE HEAD BOLT NUT TO 30 ft/lbs. MIN.
REFLECTOR
SECURE TO REMOTE HEAD WITH #10 SCREWS SHIPPED
WITH THE HORIZONTAL OPTICS (5) OR FOR AXIAL OPTICS,
THE SCREWS THAT ARE ALREADY INSTALLED IN THE
REMOTE HEAD (6) AND INSTALL THE LAMP SUPPORT
BRACKET
NOTE: VERIFY IF PROTECTIVE HULLS ARE REQUIRED
FOR THIS JOB. THEY MUST BE INSTALLED PRIOR TO
THE REFLECTORS.