Environmental requirements—series 370 load frames, Electrical requirements—series 370 load frames, Electrical requirements—series 370 load frames 16 – MTS Landmark Site Prep Guide User Manual
Page 16
Landmark Test System Site Prep Guide
16
Load Unit Specifications
System Component Specifications
Environmental Requirements—Series 370 Load Frames
All Series 370 load frames are intended for indoor use only. This indoor
environment must conform to the following environmental specifications.
Note
All Series 370 load frames must only be operated under the installation
and ambient conditions (such as, temperature, moisture, and EMC)
specified.
Electrical Requirements—Series 370 Load Frames
Parameter
Specification
Temperature
5ºC–40ºC (41ºF–104ºF)
Humidity
10–85%, non-condensing
Altitude
2000 m (6,561 ft) maximum
Parameter
Specification
Input Voltage
115 or 230 VAC (Single phase)
Input Frequency
50 or 60 Hz
Input Current
7 A at 115 VAC, 0.4 A at 230 VAC
Environment:
Location: Indoor use only
Operating temperature 5–40°C (41–104°F)
Relative humidity 5-85% non-condensing
Maximum altitude 3000 m (9,842 ft)
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)