Prepare to run a test, Prepare to run a test 56 – MTS Model 286-31 Transient Permeability Pore Pressure Intensifier User Manual
Page 56

286.31 Transient Permeability Pore Pressure Intensifier
56
Running a Steady State Flow Test
Operation
Prepare to Run a Test
1. Install your specimen in the triaxial cell.
For the details on doing this step, see the installation section of your triaxial
cell manual.
If pore pressure becomes higher than confining pressure — even for a
second — your specimen will be damaged.
Always keep confining pressure higher than pore pressure.
2. If your Triaxial Cell has an upper pore pressure shut off valve, make sure it’s
open.
3. Apply a confining pressure to the specimen.
Confining pressure must always be higher than the pore pressure.
For the details on doing this step, see the operation section of your confining
pressure intensifier manual.
4. Pressurize the pore fluid to the desired starting pressure.
On the RSC, turn the Manual Control control slowly until you reach the
desired pore pressure.
5. If the rest of your system is ready, start your data acquisition procedure.
CAUTION
- Series 111 Accumulator (40 pages)
- Series 249G2 Swivels (34 pages)
- Series 201 Actuators (40 pages)
- Series 215 Rotary Actuator (68 pages)
- Series 242 Actuators (40 pages)
- Series 244 Actuators (68 pages)
- Series 247 Actuators (40 pages)
- Series 248 Actuators (46 pages)
- 709 Alignment System (158 pages)
- Series 609 Alignment Fixture (70 pages)
- 494 Controller Hardware FT 40 (344 pages)
- ReNew Technical Reference (50 pages)
- DCPD Measurement System (46 pages)
- Bionix EnviroBath (40 pages)
- FGW900 High-temperature Furnace (38 pages)
- Model 409.83 Temperature Controller (40 pages)
- Series 651 Environmental Chambers (30 pages)
- Series 653 High-Temperature Furnaces (38 pages)
- Series 658 Environmental Chamber (24 pages)
- Series FEC Environmental Chamber (48 pages)
- Model 685.53 Grip Control Module (24 pages)
- Series 685 Hydraulic Grip Supply (48 pages)
- Bend Fixture-10 kN (2 pages)
- Grip-Manual Bend Fixture-100 kN (2 pages)
- Grip-Manual Bollard-2 kN (2 pages)
- Grip-Manual Bollard-500 N (2 pages)
- Compression Platen-100 kN-100mm (2 pages)
- Compression Platen-100 kN-150mm (2 pages)
- Compression Platen-100 kN-200mm (2 pages)
- Compression Platen-20 kN (2 pages)
- Compression Platen-20 kN-100mm (2 pages)
- Compression Platen-20 kN-200mm (2 pages)
- Compression Platen-20 kN-SST (2 pages)
- Compression Platen-500 N FYC502A (2 pages)
- Compression Platen-500 N FYB502A (2 pages)
- Compression Platen-500 N-50mm (2 pages)
- Grip-Pneumatic Vise-Style-1 kN (2 pages)
- Pneumatic Bollard-500 N (2 pages)
- Scissor-Style-2 kN (2 pages)
- Scissor-Style-5 kN (2 pages)
- Screw-Style-5 kN (2 pages)
- Screw-Style-5 kN-SST (2 pages)
- Bend Fixture-1000 kN (2 pages)
- Bend Fixture-300 kN (2 pages)
- Bolt Grips (32 pages)