Lenze 9400 Mounting Instructions - Manual (Page 56)

Technical data
Electrical data
3
l
56 EDK94ASH24 DE/EN/FR/ES/IT 4.1
Output data
Voltage Frequency 1) Current [A] Number of
phases
Type [V] [Hz] max. +45 °C

max. +55 °C

E94ASxE0024 0 − 230/400/500 0 − 599 1.5/1.5/1.3 1.1/1.1/1.0 3
E94ASxE0034 0 − 230/400/500 0 − 599 2.5/2.5/2.2 1.9/1.9/1.7 3
E94ASxE0044 0 − 230/400/500 0 − 599 4.0/4.0/3.5 3.0/3.0/2.6 3
E94ASxE0074 0 − 230/400/500 0 − 599 7.0/7.0/6.1 5.3/5.3/4.6 3
E94ASxE0134 0 − 230/400/500 0 − 599 13.0/13.0/11.4 9.8/9.8/8.6 3
E94ASxE0174 0 − 230/400/500 0 − 599 16.5/16.5/14.4 12.4/12.4/10.8 3
E94ASxE0244 0 − 230/400/500 0 − 599 23.5/23.5/20.6 17.6/17.6/15.5 3
 Temperature in the control cabinet
Power loss P
V
[W]
Type when operating with rated output current I
aN
when controller is inhibited
E94ASxE0024 110
40
E94ASxE0034 130
E94ASxE0044 160
E94ASxE0074 210
E94ASxE0134 320
E94ASxE0174 380
E94ASxE0244 500
Rated data for internal brake chopper
Switching
threshold
(adjustable)
Minimum
brake resistor
Peak current Peak braking
power
Continuous
current
RMS
Continuous
braking
power
Type U
BRmax
[V] R
Bmin
[ W] I
BRmax
[A] P
BRmax
[kW] I
BRd
[A] P
Bd
[kW]
E94ASxE0024 390/790 47/82 8.3/8.8 3.2/6.4 3.7/3.9 0.6/1.3
E94ASxE0034 390/790 47/82 8.3/8.8 3.2/6.4 3.7/3.9 0.6/1.3
E94ASxE0044 390/790 27/47 14.4/15.4 5.6/11.2 5.9/6.3 1.0/1.9
E94ASxE0074 390/790 27/47 14.4/15.4 5.6/11.2 6.9/7.4 1.3/2.6
E94ASxE0134 390/790 18/27 21.7/26.9 8.5/19.5 10.6/13.2 2.0/4.7
E94ASxE0174 390/790 9/18 43.3/40.3 16.9/29.2 20.3/18.9 3.7/6.4
E94ASxE0244 390/790 9/18 43.3/40.3 16.9/29.2 24.5/22.8 5.4/9.3
Assignment of installation backplane ˘ standard device
Axis controller
type Installation
backplane type
Busbar mounting set / fuse 1) Device size
E94ASxE0024
E94AZPS0034 E94AZJA003/ EFSAR0016ARHN I
E94ASxE0034
E94ASxE0044
E94AZPS0074 E94AZJA007/ EFSAR0040ARHN II
E94ASxE0074
E94ASxE0134
E94AZPS0244
E94AZJA024/ EFSAR0100ARHN
(tightening torque: 3.4 Nm
(30lb−in))
III E94ASxE0174
E94ASxE0244
1) The busbar mounting set with fuse is available as an accessory. It is required when Single Drives are operated in
DC−bus connection via the DC busbar.