EUCHNER MGB-L0-xxxAPx-xxx - Manual (Page 28)

28
Operating Instructions MGB-L0...AR.-... and MGB-L0...AP.-...
12 Technical data
Note:
If a product data sheet is included with the product, the information on the data
sheet applies in case of discrepancies with the operating instructions.
Parameter Value Unit
Housing material Glass fiber reinforced plastic
die-cast zinc, nickel-plated
Stainless steel
Dimensions See section 6.4 Dimension drawing, page 9
Weight
Interlocking module
Handle module
Escape release
0.75
1.00
0.50
kg
Ambient temperature at U
B
= DC 24 V -20 .... +55 °C
Degree of protection
Cover not populated/populated with buttons/indicators
Cover populated with key-operated switch
Cover populated with key-operated switch FS22
IP65
IP54
IP42
Safety class III
Degree of contamination 3
Installation position Any
Connection 4 cable entries M20x1.5 or plug connector
Conductor cross-section (rigid/flexible)
- With ferrule according to DIN 46 228/1
- With ferrule with collar according to DIN 46
228/1
0.13 ... 1.5 (AWG 24 ... AWG 16)
0.25 ... 1.5
0.25 ... 0.75
mm²
Operating voltage UB (reverse polarity protected,
regulated, residual ripple < 5 %)
24 +10% / -15% (PELV) V DC
Auxiliary power UA (reverse polarity protected,
regulated, residual ripple < 5 %)
24 +10% / -15% (PELV) V DC
Current consumption I
UB
(no load on any outputs) 80
mA Current consumption I
UA
- Push button S (no load, per LED) 5
External fuse See section 10.2 Fuse protection for power supply, page 18
Safety outputs FO1A/FO1B Semiconductor outputs, p-switching, short circuit-proof
Test duration after power on AR < 1000 / AP < 300 µs
Output voltage U
FO1A
/ U
FO1B
1)
HIGH U
FO1A
/ U
FO1B
U
B
-2V ... U
B
LOW U
FO1A
/ U
FO1B
0 ... 1 V DC
Switching current per safety output 1 ... 200 mA
Utilization category according to EN IEC 60947-5-2 DC-13 24 V 200 mA
Caution: outputs must be protected with a free-wheeling diode in case of inductive loads.
Classification acc. to EN IEC 60947-5-3 PDF-M
Monitoring outputs
- Output voltage 1)
- Max. load
p-switching, short circuit-proof
U
A
- 2V ... U
A
max. 50 mA
Rated insulation voltage U
i
30 V
Rated impulse withstand voltage U
imp
1.5 kV
Resilience to vibration In acc. with EN IEC 60947-5-3
Switching frequency 0.25 Hz
EMC protection requirements In acc. with EN IEC 60947-5-3
Reliability values according to EN ISO 13849-1
Category 4
Performance Level PL e
PFH
d
3.1 x 10 -9 / h 2)
Mission time 20 years
Controls and indicators
Operating voltage 5 … 24 V
Operating current 1 … 100 mA
Breaking capacity max. 250 mW
Power supply LED 24 V DC
1) Values at a switching current of 50 mA without taking into account the cable lengths.
2) Applying the limit value from EN ISO 13849-1:2008, section 4.5.2 (MTTF
d
= max. 100 years), the employers' liability insurance
association certifies a PFH
d
of max. 2.47 x 10 -8 .