Limited warranty – Clarus Environmental WW4 Filter Sock User Manual

Page 2

Limited Warranty

Manufacturer warrants, to the purchaser and subsequent owner during the

warranty period, every new product to be free from defects in material and

workmanship under normal use and service, when properly used and maintained,

for a period of one year from date of purchase by the end user, or 18 months

from date of original manufacture of the product, whichever comes first. Parts

that fail within the warranty period, one year from date of purchase by the

end user, or 18 months from the date of original manufacture of the product,

whichever comes first, that inspections determine to be defective in material or

workmanship, will be repaired, replaced or remanufactured at manufacturer's

option, provided however, that by so doing we will not be obligated to replace

an entire assembly, the entire mechanism or the complete unit. No allowance

will be made for shipping charges, damages, labor or other charges that may

occur due to product failure, repair or replacement.

This warranty does not apply to and there shall be no warranty for any material

or product that has been disassembled without prior approval of manufacturer,

subjected to misuse, misapplication, neglect, alteration, accident or act of

God; that has not been installed, operated or maintained in accordance with

manufacturer's installation instructions; that has been exposed to outside

substances including but not limited to the following: sand, gravel, cement,

mud, tar, hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents, etc.),

or other abrasive or corrosive substances, wash towels or feminine sanitary

products, etc. The warranty set out in the paragraph above is in lieu of all other

warranties expressed or implied; and we do not authorize any representative or

other person to assume for us any other liability in connection with our products.

Contact manufacturer at, 3649 Cane Run Road, Louisville, Kentucky 40211,

Attention: Customer Service Department to obtain any needed repair or

replacement of part(s) or additional information pertaining to our warranty.

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL,

CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH OF

EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED WARRANTY

OF FITNESS FOR A PARTICULAR PURPOSE AND OF MERCHANTABILITY

SHALL BE LIMITED TO THE DURATION OF THE EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty,

so the above limitation may not apply to you. Some states do not allow the

exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

This warranty gives you specific legal rights and you may also have other rights

which vary from state to state.

Fig. 5

SCH40 PVC TEE

SDR35 PVC TEE

“WW4” FILTER

OUTLET

SDR35 PVC TEE

“WW4” FILTER

RISER OFFSET 5"

30" RISER

REQUIRED

LIQUID PENETRATION PIPE

4" DIA PVC PIPE

SCH 40 OR SDR 35

(SUPPLIED BY OTHERS)

SEPTIC TANK

OUTLET

4" DIA. PVC PIPE, SCH 40

OR SDR35(SUPPLIED BY OTHERS)

CLARUS 24" DIA.

SEPTIC TANK RISER

CAST IN PLACE

21 7/32"

25 5/32"

26 1/4"

LEG BOSSES ACCEPT EITHER

1 1/4" OR 1 1/2" SCH 40 PVC PIPE

PVC "LEGS"

(SUPPLIED BY OTHERS)

11"

SECONDARY FILTER

PRIMARY FILTER

ASSEMBLY

FILTER CONTAINER

SECONDARY FILTER

PULL ROD (18")

PRIMARY FILTER

PULL ROD (24")

SK2318A

SK2318B

SERVICING

A routine maintenance schedule must be set up for each commercial

application. Each application will vary depending on the amount

and type of waste generated by the application. During the first

two months of filter installation, the filter should be checked

every two weeks.

To clean, withdraw the primary filter (long handle) with the Filter

Sock attached and rinse back into the septic tank and replace. Next,

remove the secondary filter (1/16" protection short handle), rinse

and replace.

Cleaning the Filter Sock can be performed by business personnel or

a service company. If a service company is used, the primary filter

with Filter Sock should be placed in a large plastic bag for pickup

by the service company. As an alternative, landfill the dirty sock and

replace it following the instructions on page 1 of this sheet. A clean

primary filter assembly with Filter Sock should be placed back into

the WW4 housing. Remove the secondary filter and clean off. An

extra primary filter assembly with Filter Sock should be kept on hand

by the business and service company. Depending on the amount

of waste generated by the application, service intervals may be as

short as a few days.

Fig. 6