Atop Technology EH7310 Series - Manual (Page 2)

Warranty Policy
Warranty Conditions
Products supplied by Atop Technologies are covered in this
warranty for sub-standard performance or defective workmanship.
The warranty is not, however, extended to goods damaged in the
following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock,
earthquake
(c) Use of unqualified power supply, connectors, or maintenance
procedure
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA" number from
Atop before shipping the goods to be repaired to Atop. When in
normal use, a sold product shall be replaced with a new one
within 3 months after purchase. The shipping cost from the
customer to Atop will be reimbursed by Atop.
After 3 months and still within the warranty period, it is up to
Atop whether to replace the unit with a new one; normally, as
long as a product is under warranty, all parts and labor are free
of charge to the customers.
After the warranty period, the customer shall cover the cost for
parts and labor.Three months after purchase, the shipping cost
from the customer to Atop will not be reimbursed, but the
shipping cost from Atop to the customer will be paid by Atop.
Limited Liability
Atop shall not be held responsible for any consequential losses
from using Atop’s product.
Warranty
5 Years
Product Categories
Serial-to-Ethernet Server
Serial-to WLAN Server
Industrial Wireless Ethernet Device
Modbus Gateway Series
Industrial Ethernet Switch
Embedded Serial Server
Pick-to-Light System
Auto-Identification and Data Collection-AIDC
1 Year
Warranty Period
※ Warranty coverage for accessories such as power
adapters and high-gain antenna is one year.
─ Any change by website in material announcement primarily. ─
The warranty certification will not be effective until an authorized
stamp issued by Atop’s overseas agents.
Purchase Date: / / (yyyy/mm/dd)
Serial Number:
ATOP Customer Services and Supports
1. Please contact your local dealers or Atop Technical Support
Center at the following numbers.
+ 886-3-550-8137 (Atop Taiwan)
+ 86-21-6495-6232 (Atop China)
2. Please report the defected problems via Atop’s Web site or
E-mail account
Web Site：www.atop.com.tw, e-mail：[email protected]
Web Site：www.atop.com.cn, e-mail：[email protected]
100Base-Fx Fiber SC/ST Cable Wiring
ST Connector
SC Connector
TX
RX A
B RX
TX B
A ←
TX
RX A
B RX
TX B
A ←
10/100Base-T(X) Ethernet Port Connection
RJ-45
Pin
Signal 1 2 3 4 5 6 7 8
Configuration and Setting Methods
Any settings or configuration is unnecessary.
Pin Assignment of Network
Connections
1 8
Tx+ Tx- Rx+ Rx-
Cable type, Max. Transmission and Connector
10Base-T
100Base-TX
1000Base-TX
1000Base-SX
1000Base-LX
100Base-Fx Fiber SC/ST Port Connection
Fiber Port
SC Connectors ST Connectors
Single-mode Multi-mode
Tx
Rx
Tx
Rx
Cable Type Max. Length Connector
Cat. 3, 4, 5
Cat. 5 UTP
Cat. 5/Cat. 5e UTP
850µm, multi-mode
1310µm, single-mode
UTP 100 m (328 ft)
UTP 100 m (328 ft)
UTP 100 m (328ft)
550m
5 km
RJ-45
RJ-45
RJ-45
SC
SC
EH7310 series mechanical
dimensions(unit=mm)
There are four LED indicators located at the front panel of
EH series.
7-pin Terminal Block for Power Input
1. Grounding screw
2. Hardware Reset Button
3. Frame Ground
4. Terminal block for power input
PWR1
5. Relay output warning for power failure and break alarm.
Normally Closed.(1A@24VDC)
6. Terminal block for power input PWR2
1 2 3 4 5 6
G V1- V1+ V2- V2+
PWR1 Relay PWR2
13
8,2
0
13
8,2
0
4,0
0
6,0
0
38
,6
0
12
,5
0
17
,9
5
32
,6
0
19
,3
0
45,90
38
,6
0
Real View Panel Mountinrg View
Front View
EH7310
Front View
EH7310-G-2Fm
EH7310-G-2Fs
EH7310-2Fm
EH7310-2Fs
14
1,2
5
46,20
2-port 10/100/1000Base T(X) (copper)
or 2-port 100Base FX (SC connector)
or 2-port 1000Base FX (SC connector)
8-port 10/100Base T(X)
(RJ-45) shielding with LED
Botton View
Redundant inputs Power Supply
(12/24/48 VDC)
PWR1 or PWR2
Failure to Tigger Fault
(Normally Closed) (1A@24 VDC)
Side View
14
5,
70
117,85
DIN-Rail Mount