Atop Technology EF23G-1G - Manual

Industrial Ethernet to Fiber Media Convertor
Hardware Installation Guide
Version 1.1
Updated on Dec, 2011
Introduction Inside the Package
Product Description
EF23 Series
Technologies
Tel: 886-3-5508137
Fax: 886-3-5508131
www.atop.com.tw
EF23 Series
10/100 Base-TX to 100Base-Fx Media Converters
EF23G Series
1000Base-TX to 1000Base-FX Media Converters
Atop Technologies, Inc.
Thank you for choosing the Atop Industrial DIN-Rail Ethernet to
Fiber Media Converter. The EF23/EF23G Series provide industrial
grade media conversion between 10/100Base-TX and
100Base-FX (SC connectors)/1000base-T(X) and
1000Base-FX(SC connectors/SFP).
This Guide covers Five product models:
EF23 Series
■
EF23-1-Fm-SC-2:
Fast Ethernet 10/100Base-TX to 100Base-FX Media Converter
with extended operating temperature.
Include 1 10/100M RJ45 and 1 100M Multi-mode Optical Fiber.
■
EF23-1-Fs-SC-30:
Fast Ethernet 10/100Base-TX to 100Base-FX Media Converter
with extended operating temperature.
Include 1 10/100M RJ45 and 1 100M Single-mode Optical Fiber.
EF23G Series
■
EF23-1G-1Fm-SC-500M:
Gigabit Ethernet 1000Base-TX to 1000Base-FX Media Converter
with extended operating temperature.
Include 1 1000M RJ45 and 1 1000M Multi-mode Optical Fiber.
■
EF23-1G-1Fs-SC-10:
Gigabit Ethernet 1000Base-TX to 1000Base-FX Media Converter
with extended operating temperature.
Include 1 1000M RJ45 and 1 1000M Single-mode Optical Fiber.
■
EF23-1G-1SFP:
Gigabit Ethernet 1000Base-TX to 1000Base-SX/LX/LHX Media
Converter with extended operating temperature.
Include 1 1000M RJ45 and 1 1000M SFP slot.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received; including
interference that may cause undesired operation.
■
Main Product
■
Atop EF23/EF23G industrial Ethernet Media Converter x1
■
Standard accessories
■
3-pin Terminal Block (2ESDVM-03P) x1
Atop P/N: 50706701G
■ RJ-45 Port Plugs x1
Atop P/N: 3990012G
■ Hardware Installation Guide (Warranty card is include) x1
Atop P/N: 89900403G
Optional Accessories
■
3-pin Terminal Block(2ESDVM-03P )
Atop P/N: 50706701G
■
Adapter : 3-pin Terminal block (5.08 mm) power adaptor,
100-240VAC input, 1.25A @ 12VDC output, US
plug
Atop P/N: 70100000000027G
■
Adapter : 3-pin Terminal block (5.08 mm) power adaptor,
100-240VAC input, 1.25A @ 12VDC output, EU
plug
Atop P/N: 70100000000028G
Hardware Installation
■
Electrical
Step 1: Unpack the Media Converter, check
to make sure no external damages.
Step 2: Connect the power jack with the power
adapter. It is normal to see the PWR
indicator on.
Step 3: Hook up one RJ-45 port to your LAN, and
other port to your computer. Check to mark
sure your host computer can access the LAN.
Step 4: Hook up one FIBER port to other
EF23 series, It is normal to see
the FX_LINK/ACT indicator on.
■
Mechanical
Media Converters are equipped with DIN-Rail bracket attached onto rear
panel. Follow the steps below to fasten the Media Converter to DIN-Rail.
Step 1: Tilt the unit slightly backwards.
Step 2: Fit the unit over top the DIN-Rail.
Step 3: Push downwards and against the DIN-Rail for locking.
Step 4: Check that the unit is locked into position.
1. TX Port: 10/100 Base-TX
2. Green: PWR SPD LED
3. Green: TX_LINK/ACT TX_FDX/COL LED
4. Green: FX_LINK/ACT FX_FDX/COL LED
5. FX Port: 100 Base-FX (SC Connector)
EF23G Series
1. TX Port: 1000 Base-TX
2. Green: ACT TX_LINK
3. Green: PWR FX_FDX/COL LED
4. FX Port: 1000 Base-FX
(SC Connector or SFP Solt)
EF23 Series LED Indicators
LED
PWR
SPD
TX_LINK\ACT
TX_FDX/COL
FX_LINK\ACT
FX_FDX/COL ON
ON
100M
Link up
Full
Link up
Full OFF
OFF
10M
Link down
Half
Link down
Half Flash
Link up/Active
Half/Col happen
Link up/Active
Half/Col happen
EF23G Series LED Indicators
LED
ACT
TX_LINK\ACT
PWR
FX_LINK\ACT ON
Link up
ON
Link up
OFF
Link down
OFF
Link down
Flash
Transmitting or Receiving
PWR
Link up/Active
* SPD only for TX
WARNING:
Disconnect the power and allow to cool 5 minutes
before touching.
Never install or work on electrical or cabling during
periods of lighting activity. Never connect or disconnect
power when hazardous gases are present.
Caution:
CLASS 1 LASER PRODUCT. Do not stare into the laser!