Atop Technology EHG6308 Series - Manual (Page 2)

Warranty Policy
Warranty Conditions
Products supplied by Atop Technologies are covered in this
warranty for sub-standard performance or defective workmanship.
The warranty is not, however, extended to goods damaged in the
following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock,
earthquake
(c) Use of unqualified power supply, connectors, or maintenance
procedure
(d) Replacement with unauthorized parts
RMA and Shipping Costs Reimbursement
Customers shall always obtain an authorized "RMA" number from
Atop before shipping the goods to be repaired to Atop. When in
normal use, a sold product shall be replaced with a new one
within 3 months after purchase. The shipping cost from the
customer to Atop will be reimbursed by Atop.
After 3 months and still within the warranty period, it is up to
Atop whether to replace the unit with a new one; normally, as
long as a product is under warranty, all parts and labor are free
of charge to the customers.
After the warranty period, the customer shall cover the cost for
parts and labor.Three months after purchase, the shipping cost
from the customer to Atop will not be reimbursed, but the
shipping cost from Atop to the customer will be paid by Atop.
Limited Liability
Atop shall not be held responsible for any consequential losses
from using Atop’s product.
Warranty
5 Years
Product Categories
Serial-to-Ethernet Server
Serial-to WLAN Server
Industrial Wireless Ethernet Device
Modbus Gateway Series
Industrial Ethernet Switch
Embedded Serial Server
Pick-to-Light System
Auto-Identification and Data Collection-AIDC
1 Year
Warranty Period
※ Warranty coverage for accessories such as power
adapters and high-gain antenna is one year.
─ Any change by website in material announcement primarily. ─
The warranty certification will not be effective until an authorized
stamp issued by Atop’s overseas agents.
Purchase Date: / / (yyyy/mm/dd)
Serial Number:
ATOP Customer Services and Supports
1. Please contact your local dealers or Atop Technical Support
Center at the following numbers.
+ 886-3-550-8137 (Atop Taiwan)
+ 86-21-6495-6232 (Atop China)
2. Please report the defected problems via Atop’s Web site or
E-mail account
Web Site：www.atop.com.tw, e-mail：[email protected]
Web Site：www.atop.com.cn, e-mail：[email protected]
10/100/1000Base-T(X) Ethernet Port Connection
RJ-45
Pin
Signal
Pin
Signal
1 2 3 4 5 6 7 8
1 2 3 4 5 6 7 8
Configuration and Setting Methods
Any settings or configuration is unnecessary.
Pin Assignment of Network
Connections
1 8
Tx+
DC+
Rx+
DC -
Rx -
DC -
Tx -
DC+
Cable type, Max. Transmission and Connector
1000Base- Fiber SFP Port Connection
10Base-T
100Base-T
1000Base-T
1000Base-SX\SX+
1000Base-LX\LHX\XD
Speed Cable Max. Length Connector
Cat. 3, 4, 5
Cat. 5 UTP
Cat. 5/Cat.5e UTP
Multi-mode
Single-mode
UTP 100 m
(328 ft)
UTP 100 m
(328 ft)
UTP 100 m
(328 ft)
2km
30 km
RJ-45
RJ-45
RJ-45
SFP
SFP
7-pin Terminal Block for Power Input
1. Grounding screw
2. Frame Ground
3. Terminal block for power input PWR1
4. Relay output warning for power failure and break alarm.
Normally Closed.(1A@24VDC)
5. Terminal block for power input PWR2
1 2 3 4 5
G V1- V1+ V2- V2+
PWR1 Relay PWR2
10/100Base –T(X)
1000base-T(X)
TxRx
A+
DC+
TxRx
A -
DC+
TxRx
B -
DC -
TxRx
B+
DC -
TxRx
C+
TxRx
D+
TxRx
D -
TxRx
C -
Fiber Port
Single-mode & Multi-mode
Note:
The above picture shows the optional accessories available upon request.
EHG6308 series
Physical appearance and Dimensions
(unit=mm)
13
8,2
0
13
8,2
0
4,0
0
6,0
0
38
,6
0
12,50
17
,9
5
32
,6
0
19
,3
0
45,90
38
,6
0
Real View Panel Mountinrg View
Front View
EHG6308-4PoE
Front View
EHG6308-4PoE-SFP
14
1,2
5
Top View
Redundant inputs Power Supply
(48V~57V VDC)
PWR1 or PWR2
Failure to Tigger Fault
(Normally Closed) (1A@24 VDC)
Side View
14
5,
70
117,85
DIN-Rail Mount
46,20
PWR1PWR2Fault
1
2
3
4
PoE
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
LAN
PWR1PWR2Fault
1
2
3
4
PoE
1
2
3
4
5
6
7
8
1
2
3
4
5
6
7
8
LAN