9 safety decals – Echo 76628S User Manual

Page 9

PN 14295-00 R

SAFETY

See Section 1.10 for decal locations. Familiarize yourself with all of the safety and operating decals on the machine and the associ-

ated hazards. See the engine owners manual or contact the engine manufacturer for engine safety instructions and decals. Make

certain that all safety and operational decals on this machine are kept clean and in good condition. The decals are shown below at
reduced sizes. Refer to the parts catalog if you need a replacement decal. decals that need replacement must be applied to their
original locations.

1.9 saFety DeCals

KEEP HANDS AND FEET OUT OF

INLET AND DISCHARgE OPENINgS

WHILE MACHINE IS OPERATINg
to aVoId SERIouS PERSoNaL IN-

JURY. STOP AND ALLOW MACHINE
to CoME to a CoMPLEtE StoP

BEFORE CLEARINg OBSTRUC-
tIoNS.

PN 12175

PN 12173

DO NOT OPERATE THIS EQUIPMENT

IN THE VICINITY OF BYSTANDERS.

DO NOT ALLOW CHILDREN TO OP-

ERATE THIS EQUIPMENT. ALWAYS

STAND CLEAR OF DISCHARgE AREA

WHEN OPERATINg THIS MACHINE.

KEEP FACE AND BODY AWAY FROM

DISCHARgE AREAS.

REad aNd uNdERStaNd thIS

OWNER/OPERATORS MANUAL.

BE COMPLETELY FAMILIAR

WITH THE CONTROLS AND THE

PROPER USE OF THIS EQUIP-
MENt.

PN 13711-00

PN 12169

KEEP HANDS AND FEET OUT OF INLET AND

DISCHARgE OPENINgS WHILE MACHINE IS OPERAT-

INg TO AVOID SERIOUS PERSONAL INJURY. STOP

AND ALLOW MACHINE TO COME TO A COMPLETE

STOP BEFORE CLEARINg OBSTRUCTIONS.

READ AND UNDERSTAND THIS OWN-
ER/oPERatoRS MaNuaL. bE CoM-

PLETELY FAMILIAR WITH THE CON-

TROLS AND THE PROPER USE OF

THIS EQUIPMENT

OBTAIN AND WEAR SAFETY gLASS-

ES AND USE HEARINg PROTECTION

AT ALL TIMES WHEN OPERATINg
thIS MaChINE.

BEFORE INSPECTINg OR SERVICINg

ANY PART OF THIS MACHINE, SHUT

OFF POWER SOURCE, DISCONNECT

SPARK PLUg WIRE FROM SPARK

PLUg AND MAKE SURE ALL MOVINg
PaRtS haVE CoME to a CoMPLEtE
StoP.

PN 12172

PN 12174

DO NOT OPERATE MACHINE WITHOUT SHIELDS IN

PLACE. FAILURE TO DO SO MAY CAUSE SERIOUS

INJURY OR DEATH.

CHECK BLADE BOLTS FOR PROP-

ER TORQUE AFTER EVERY 8

HOURS OF OPERATION. CHECK
bLadES aNd RotatE oR RE-

SHARPEN DAILY OR AS REQUIRED
to kEEP bLadES ShaRP. RE-

FER TO OWNERS MANUAL FOR

INSTRUCTIONS. FAILURE TO DO

SO MAY CAUSE POOR PERFOR-

MANCE, DAMAgE OR PERSONAL

INJURY AND WILL VOID THE MA-

CHINE WARRANTY.

PN 12250

do Not oPERatE ChIPPER

WITHOUT TURNTABLE BASE

LOCKED IN PLACE. FAILURE TO

DO SO MAY RESULT IN DAMAgE
to MaChINE aNd/oR SERIouS

BODILY INJURY.

FOR TRANSPORT, RETURN
ChIPPER to tRaNSPoRt Po-
SItIoN, INSERt tRaNSPoRt

SAFETY PIN AND CLIP, AND SET
tuRNtabLE bRakE haNdLE

TO LOCKED POSITION. FAIL-

URE TO DO SO MAY RESULT IN

DAMAgE TO MACHINE AND/OR

SERIOUS BODILY INJURY.

PN 18606-00