Aries Automotive 3062-2 - Manual (Page 2)

remove the bolt and tool from the Metal Insert. Repeat this step for second hole and for installation of
the remaining Threaded Metal Inserts for the driver side Mounting Bracket installation. NOTE: It is not
necessary but to make installation of the Threaded Inserts easier, remove the plastic bumper cover.
5. Position the passenger side Mounting Bracket up to the cross member and over the previously installed
Rod Bolt. Secure Mounting Bracket to Rod Bolt with (1) 10mm Flat Washer and (1) 10mm Nylon Lock
Nut, (Figure 6). Do not tighten hardware at this time.
6. Attach the Mounting Bracket to the (2) threaded holes in the end of the cross member.
2008 Models: Use (2) 10mm x 30mm Hex Bolts, (2) 10mm Lock Washers and (2) 10mm Flat Washers,
(Figure 5 & 6). Do not tighten hardware at this time.
2009-2012 Models: Insert (2) 8mm x 30mm Hex Bolts, (2) 8mm Lock Washers and (2) 8mm Flat
Washers into the threaded inserts installed in Step 4, (Figure 5 & 6). Do not tighten hardware at this
time.
7. Move up to the passenger side of the grille opening. Locate and remove the fastener at the top-left
hand corner of the grille opening, (Figure 7). Insert (1) 8mm x 25mm Bolt Plate into and down through
the factory hole left by the plastic fastener, (Figure 8).
8. Select the passenger side Top Bracket and hang it from the previously installed Bolt Plate with (1) 8mm
Flat Washer and (1) 8mm Nylon lock Nut, (Figure 9). Do not tighten at this time.
9. Repeat steps 3 - 8 for the driver side Bracket installation.
10. With assistance, position the Grille Guard up to the outside of the Mounting Brackets and Top Brackets.
Attach Grille Guard to Mounting Brackets using (6) 12mm x 30mm Hex Bolts, (12) 12mm Flat Washers
and (6) 12mm Nylon Lock Nuts, (Figure 10). Do not tighten at this time.
11. Attach Grille Guard to the Top Brackets with (2) 10mm x 25mm Button Head Bolts, (4) 10mm Flat
Washers and (2) 10mm Nylon Lock Nuts, (Figure 11). Do not tighten at this time
12. Level and adjust Grille Guard and tighten all hardware at this time.
13. One at a time, hold each of the splash guards and the spoiler up into position to determine the area that
will need to be removed to clear the Mounting Brackets. To maintain strength, only remove the
minimum amount of material to clear the Mounting Brackets. Using a hacksaw, cut out 3/4” wide slot on
each marked location on the air dam shown in Figure 12A & 12B. NOTE: The air dam will be in three
pieces when re-installed.
14. Cut out a 1-1/4” x 4” wide slot in each marked location on both plastic splash guards as shown in
Figure 12A & 12B. Once the air dam and plastic shroud are cut re-install them using the factory screws
removed in Step 2. NOTE: (2) longer 6mm x 30mm Screws, (2) 6mm Lock Washers and (2) 6mm Flat
Washers have been included to go through the Mounting Brackets for the Grille Guard, the spoiler and
the splash guards, (Figure 12A & 12B).
15. Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing is recommended to add a
protective layer over the finish. Do not use any type of polish or wax that may contain abrasives that could
damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and scuffs on the finish. Mild
soap may be used also to clean the Grille Guard.
For gloss black finishes: Mild soap may be used to clean the Grille Guard.
Page 2 of 5 10/29/13