Synergy 5801 - Jeep JK 2/4 Dr Front Grab Handle User Manual
Page 8
12. Slip the J-Hook side of the grab handle through the hole cut in step 8. Slip from the back / inside of the A-
pillar trim. See image below.
13. Install the grab handle and A-pillar trim simultaneously.
14. Begin by bolting the grab handle to the windshield using the factory bolt removed in step 5. Do not fully
tighten at this time, simply snug into position.
15. Fasten A-pillar trim back to the vehicle by lining up the push-pin locations and pressing into position.
Reinstall push-pin fastener #6 and corresponding screw insert which was removed in step 3.
See also other documents in the category Synergy For the car:
- 3427 - Univ Jeep Shock Stem Adapter (1 page)
- 4012 - Jeep JK Spare Tire Relocation Bracket (1 page)
- 4018 - Jeep JK Compressor Mount (3 pages)
- 4018-RHD - JK Onboard Air Compressor Bracket RHD (Viair & ARB) (4 pages)
- 4024 - Jeep JK Air Tank Mount (2 pages)
- 4034 - Air Compressor Bracket 12+ JK w/ 3.6L Pentastar (4 pages)
- 4040 - Synergy Sit Shower Shave Kit (21 pages)
- 4105 / 6 - D60 Drive Gears (1 page)
- 4120 Series - Heavy Duty Ball Joints (1 page)
- 4121/21-01 - Heavy Duty Ball Joints (1 page)
- 4122/22-01 - Heavy Duty Ball Joints (1 page)
- 4124 - Heavy Duty Ball Joints (2 pages)
- 4125 - HD Ball Joints for 80-96 Ford Bronco, F150, F250 (1 page)
- 4128 - Heavy Duty Ball Joints (1 page)
- 4129/29-01 - Jeep XJ Heavy Duty Front Ball Joints (2 pages)
- 413402 - Low Misalignment Tie Rod End Dust Boot (3 pages)
- 414X - GM HD Ball Joints (1 page)
- 5000 - Jeep TJ Front Coilover Bracket Kit (4 pages)
- 5011 - Jeep JK Front Coil Over Mounting Kit (17 pages)
- 5011-03 - Jeep JK Front Air Bump Mounting Kit (5 pages)
- 5012 - Jeep TJ/YJ/CJ Universal Shock Hoop (6 pages)
- 5013 - Jeep JK Rear Coilover Kit (13 pages)
- 5014-A - Jeep JK Rear Air Bump Kit (10 pages)
- 5016 - Jeep JK Unlimited Three Seat Bracket (7 pages)
- 5017 - 2012+ Jeep JK Exhaust Spacer Kit (9 pages)
- 5019 - Jeep JK Thru Coil Front Air Bump Kit (10 pages)
- 5021 - Jeep JK Heavy Duty Front Lower Control Arm Frame Bracket (10 pages)
- 5022-02 - Jeep JK Frame Side RLCA Gusset Kit (12 pages)
- 5051 - Front 3 Link Kit for Jeep TJ (16 pages)
- 5052 - Rear 4 Link Kit (Bronco, Jeep CJ, TJ, YJ, Universal) (10 pages)
- 5102-0X - Jeep JK Louvered Hood Panel (13 pages)
- 5103 - Jeep JK License Plate Delete Panel (3 pages)
- 5203 - Jeep TJ/LJ Front Cage Kit (10 pages)
- 5204 - Jeep TJ Rear Cage Kit (6 pages)
- 5205 - TJ/LJ Cage Tie-In Kit (4 pages)
- 5210 - Jeep LJ/TJ Cage Kit (8 pages)
- 5221 - 07-10 Jeep JK 2/4 Door Front Cage Kit (51 pages)
- 5221-A - 2011+ Jeep JK 2/4 Door Front Cage Kit (61 pages)
- 5222-04 - Jeep JK 2 Door Weld-In Harness Bar (6 pages)
- 5222-A - Jeep JK 2 Door Rear Cage Kit (10 pages)
- 5223 - JK 4 Door B-Pillar Cage Kit (15 pages)
- 5224-A - Jeep JK 4 Door Rear Cage Kit (11 pages)
- 5232-3 - Jeep YJ Rear Cage Kit (8 pages)
- 523X - Jeep YJ Cage Kit (14 pages)
- 5310 - Jeep JK Rear Bumper (10 pages)