Caution – Defi Link VSD Concept User Manual

Page 15

■When the Defi-Link Display VSD CONCEPT is used WITHOUT a connection to the Defi-Link System

■When the Defi-Link Display VSD CONCEPT is used WITH a connection to the Defi-Link System

NOTE: If "MPH,

F, PSI" is selected in the

setting of units, data other than
the engine speed is not displayed.

NOTE: If "MPH,

F, PSI" is selected in the

setting of units, data other than
the engine speed is not displayed.

NOTE: When connected to the Defi-Link System, the PEAK button of the D.C.Unit is unavailable.

⑧Rec Mode

⑩Warm-Up Mode

⑪Control Output

This Warm-Up Mode is available when either a water temperature sensor or an oil temperature sensor is
connected to Defi-Link Control Unit II

（or Defi-Link Control Unit) and the setting of Warm-Up is completed. After

Opening Mode, Warm-Up Mode starts if the sensor data is below the set value. During this mode, leftmost
digital segments are lighted in order. If the displayed data is changed by pressing the SELECT button during
this mode, the unit of temperature blinks(

℃/°

F). When the temperature reaches the set value, Warm-Up Mode

is completed and returns to Real Mode.

This Control Output function is available when either a water temperature sensor or an oil temperature sensor
is connected to Defi-Link Control Unit II

（or Defi-Link Control Unit) and the setting of Control Output is

completed.

When the temperature reaches the set value, the Control Output signal is read out to the terminal of

CONT. OUT of D.C.Unit.

I)If the auto warning mode is turned ON in the setting of auto warning

NOTE: Even if REC button is pressed in vehicle's stopped condition, the vehicle speed data cannot be

recorded and Rec Mode will turn to Play Mode.

When the vehicle is moving at the speed of 1km/h(1MPH) or more, connected sensor
data and the speed data are recorded for a maximum of 3 minutes by pressing the
REC button of Defi-Link Control Unit II(or Defi-Link Control Unit). "R" is displayed
during recording. Data displayed in the digital and bar display section can be
changed by pressing SELECT/BAR SELECT button.

When the vehicle speed is 0km/h(0MPH), recorded data are displayed by pressing the
PLAY button of Defi-Link Control Unit II(or by pressing the PLAY/REC button of Defi-
Link Control Unit during Peak Mode). "P" is displayed during playing of data. Data
displayed in the digital and bar display section can be changed by pressing
SELECT/BAR SELECT button.

⑨Play Mode

II)If the auto warning mode is turned OFF in the setting of auto warning

a)Example on direct hookup of a

warning lamp

b)Example of how to connect a motor by using a relay and how to

load a LED indicator

●Do not connect anything to the CONT. OUT connector unless this function is used.
●Load current of the Control Output is less than 300mA.
●When the special display is performed, the Control Output signal is not read out.
●Any damages to other products connected to the CONT. OUT connector is not covered by the warranty.

Caution

NOTE: Once pause, fast-forward or rewind is performed with Defi-Link Control Unit II(or Defi-Link Control Unit), the

recorded speed data cannot be played back. To play back the speed data, Play Mode needs to be started

recorded speed data cannot be played back. To play back the speed data, Play Mode needs to be started
over again. Operation needs to be performed in vehicle's stopped condition. If the PLAY button is pressed

over again. Operation needs to be performed in vehicle's stopped condition. If the PLAY button is pressed
in vehicle's running condition, speed data will not be played back but Play Mode will turn to Rec Mode.

in vehicle's running condition, speed data will not be played back but Play Mode will turn to Rec Mode.

NOTE: The pulse free setting needs to be done again if units are changed.

NOTE: If the Defi-Link Display VSD CONCEPT is linked with the Defi-Link System, the setting of Defi-

Link Control Unit II(or Defi-Link Control Unit) is prioritized.

NOTE: This function operates when the Defi-Link Display VSD CONCEPT is linked with the Defi-Link

System and the temperature sensor is connected.

NOTE: This function operates when the Defi-Link Display VSD CONCEPT is linked with the Defi-Link

System and the temperature sensor is connected.

Connect to 12V wire when ignition

is on.

Lamp

CONT. OUT
connector(red)

Relay

LED
Indicator

Diode

Resistor

Motor

CONT. OUT
connector(red)

NOTE: If the Defi-Link Display VSD CONCEPT is linked with the Defi-Link System, the tachometer

warning2 cannot be set. The setting value of the tachometer warning of Defi-Link Control Unit
II(or Defi-Link Control Unit) is applied as a tachometer warning2. Please set up the tachometer
warning of Defi-Link Control Unit II(or Defi-Link Control Unit) higher than the tachometer
warning1 value. If the value is set lower than the warning1, the warning1 will be invalid.

NOTE: If the Defi-Link Display VSD CONCEPT is linked with the Defi-Link System, the warning buzzer

of Defi-Link Control Unit II cannot be absorbed.

NOTE: This function operates when the Defi-Link Display VSD CONCEPT is linked with the Defi-Link

System.

When the auto dimmer mode is on, the brightness of the display is adjusted automatically. Press
ENTER to Select one from three stages of brightness in the auto dimmer mode during the real mode or
the peak mode. When the manual dimmer mode is on, the brightness of the display can be set
manually at 5 stages in the real mode or the peak mode.

Connect to 12V wire when ignition is on.