Philips DVP3345V-17 - Manual (Page 25)

English
Timer Recording (cont’d) 25
7 Press K or L to select a recording tape speed. The arrow
will appear beside your choice. The selected speed will flash
beside REC SPEED. Details about tape speed are on page 57.
You must select the recording speed to complete the
timer programming.
• To stop a started Timer Recording,
press STOP/EJECT C A on the
front of the DVD/VCR. (You cannot
stop a started Timer Recording with
STOP C on the remote.)
• To change incorrect information,
press s or B to choose the
item you want to change. Press
K
or L to adjust the information.
• If there is no tape in the VCR
when you press TIMER SET,
“
” will flash. Insert a tape.
• If one or more Timer Recordings
are on standby when one Timer
Recording ends, the DVD/VCR
will turn off automatically and
“
” will appear on the
DVD/VCR’s display panel
indicating that it is now ready for
another Timer Recording.
Helpful Hints
PROGRAM NUMBER 1
DATE
0 8 / 2 9 WED
START TIME 0 7 : 3 0 P M
END TIME 0 8 : 3 0 P M
L1/L2 L2
REC SPEED S P
B SP
SLP
ONE TIME PROGRAM
8 Press CLEAR to remove the menu.
9 Press TIMER SET.
● In some cases, the DVD/VCR will switch to DVD mode
instead.
You may use the DVD player during a Timer Recording.
● If you want to use the VCR until time for the recording,
don’t press TIMER SET until a few minutes before the
recording should start. Or, press TIMER SET only when you
know you won’t be using the VCR anymore (until after the
recording).
● When “ ” is lit (not flashing), you cannot put the
DVD/VCR in VCR mode by pressing VCR or SOURCE.
You must first press TIMER SET on the remote control or
STOP/EJECT C A on the front panel to cancel the Timer
Recording temporarily. Then, you can use the VCR features
again.
When a Timer Recording ends
The DVD/VCR will turn off and “ ” on the DVD/VCR’s display panel
will flash indicating that the recording is complete, then goes into the
timer standby mode again. (It may switch to DVD mode
automatically.) At this point, you cannot use the VCR unless you
release the DVD/VCR from the timer standby mode.
To release the DVD/VCR from timer standby mode
●
If the DVD component is active and no more Timer Recordings are
on standby, you can cancel the timer standby mode by pressing
TIMER SET or VCR on the remote control or by pressing SOURCE
or STOP/EJECT C A on the front panel.
●
If the DVD component is not active, or the “ ” is not flashing but
lit indicating there are more Timer Recordings on standby, you can
cancel the timer standby mode only by pressing TIMER SET on the
remote control or by pressing STOP/EJECT C A on the front panel.
●
After releasing the DVD/VCR from timer standby mode, you can use
it as usual.
Canceling a Timer Recording Before the Recording Starts
1 Press VCR, then press SETUP so MENU appears.
2 Press K or L to select TIMER PROGRAMMING,
then press B.
3 Press K or L to find the program you want to
cancel.
4 While the program number is flashing, press s to
clear all the information for that program.
5 Press CLEAR to remove the menu.
DVD VCR SETUP
INPUT MENU
REC SPEED MODE
ANGLE SEARCH REPEAT
DISPLAY SUBTITLE ZOOM
TIMER SET
REPEAT
A-B
AUDIO
BACK PAUSE STOP
PLAY
OK
FFW REW
CLEAR TITLE
DISC
TRACKING
OPEN/CLOSE
1 2
6 5 4
7 8 9
0 +10
3
7
8
9
E8E20UD_EN1 8/23/07 1:25 PM Page 25