Philips CDR770BK - Manual (Page 13)

English
19
Important:
- Recording from CD-changers should always be started in the
RECORD DISC, RECORD TRACK or MAKE CD mode.
- Only make analog recordings when digital recording is not
possible.
Preparing for manual recording
1 Make sure the disc is absolutely free of scratches and dust
particles.
2 Press SOURCE repeatedly until (depending on the
connection used):
➜ DIGITAL I, OPTICAL I or ANALOG lights up and
DIGITAL 1, OPTICAL or ANALOG will appear on
the display.
•When Auto Track is On (default setting), track numbers will
automatically be increased during recording.
• To switch off the Auto Track function, you must enter
Menu mode.
If you wish to increase track numbers manually, press
TRACK INCR(ement) on the remote control. For further
instructions see Menu mode.
ON (AUTO): The track increments are automatically taken over
from the digital source material or after 2.7
seconds of silence during analog recording.
OFF (MANUAL): While recording, track numbers can be
incremented manually by pressing TRACK
INCR(ement) on the remote control (minimum
track length is 4 sec.). (This can also be done
in Auto track on mode.)
• Track numbers cannot be changed after recording.
Note: Auto track works only with Consumer Sources with a
digital output signal according to the IEC 958
(consumer part) audio standard.
3 With the recorder stopped, press REC TYPE three times to
enter the Manual Record standby mode.
➜
MANUAL starts to flash and the display shows REC
MANUAL.
4 Play the source first to set the optimal recording level on
the CD recorder.
5 Rotate the EASY JOG/ENTER key until all the blue
segments are lighted on the Record/Play Level bar but the
red segments do not light continuously during the loudest
passages.
➜ Display shows
-XX DB (Decibel, e.g. -3 DB).
6 Stop the source.
Start recording
1 To start recording, press RECORD on the CD recorder and
immediately start the source (from stop-mode).
➜ d lights continuously. The track number and recording
time will appear on the display.
• If
CHECK INPUT message also flashes, the digital
connection is incorrect.
• To record a 3-second silence at the start of a track, press
PAUSE on the CD recorder before starting the source.
• To check the elapsed recording time, press DISPLAY on the
CD recorder. (This can also be done during the recording.)
2 To stop recording, press STOP on the CD recorder.
➜ UPDATE lights up and d goes out.
• If STOP is pressed within 3 seconds after RECORD, no
recording will take place.
• To interrupt recording, press PAUSE on the CD recorder.
d starts to flash. Resume at step 1.
After recording the display will show UPDATE for several
seconds.
Note: With
AUTO TRACK ON,, the recorder will stop and
go to REC STANDBY for 1 minute and then goes to stop
mode automatically. Recordings from DAT, DCC or
recordings made analogously will stop after 20 seconds
of silence. With
AUTO TRACK OFF, the auto stop
mode is disabled.
Important:
If you want to play the recorded CDR disc on a regular
CD player, it must be finalized. See finalizing discs .
Finalized CDRW discs play only on CDRW compatible
CD players.
REM TRACK REC TIME
DIGITAL
OPTICAL
ANALOG
PROG
SHUFFLE
REPEAT
SCAN
I
I CD
RW
SYNC MANUAL RECORD
REM TOTAL
ALL
TRACK
TIME STEP TRACK
REM TRACK TIME
DIGITAL
OPTICAL
ANALOG
PROG
SHUFFLE
REPEAT
SCAN
I
I CD
RW
SYNC MANUAL RECORD
REM TOTAL
ALL
TRACK
TIME STEP TRACK
AUDIO CD RECORDABLE/REWRIT ABLE
OPEN / CLOSE PLAY / PAUSE STOP REC
TYPE
Recordable
ON / OFF
OPEN / CLOSE PLAY / PAUSE STOP
SOURCE ERASE FINALIZE
AUDIO CD RECORDABLE/REWRIT ABLE
DISPLAY
RECORD
PHONES INFRA RED
EASY JOG STORE/ MENU
PHONES INFRA RED
EASY JOG STORE/
MENU
ENTER
CANCEL/
DELETE
Manual recording
RECORDING