Sharp MX-B200 - Manual (Page 5)

3 4
SPECIFICATIONS
*1 When standard A4 paper is used under the operating conditions.
*2 Feed paper lengthwise only.
*3 Leading and trailing edges.
*4 Along the other edges in totals.
*5 Print speed during printing of the second sheet and following sheets
when using A4 plain paper in the tray 1 and performing continuous one-
sided printing of the same page.
*6 First copy time may vary depending on the status of the machine.
*7 Warm-up time may vary depending on some environments.
*8 Not including toner cartridge.
Optional equipment
Single pass feeder (MX-SP10)
250-sheet paper feed unit (MX-CS10)
Model MX-B200
Type Digital multifunctional system, desk-top type
Copy / printer system Dry, electrostatic transfer
Originals Sheets, bound documents
Printer function Available
Scanner function Available
Paper tray 250 sheets
Multi-bypass tray 50 sheets
Paper output tray 200 sheets * 1
Original
sizes
Document
glass/SPF
Max. A4
Original
feed
Document
glass 1 sheet
SPF Up to 50 sheets
Copy / printing size A6 to A4* 2
Image loss
Max. 4 mm * 3
Max. 4.5 mm * 4
Copy speed 20 pages/min. (A4)
Print speed * 5 20 pages/min. (A4)
Continuous copying Max. 99 pages subtractive counter
First-copy time * 6
(Approximately)
8.0 seconds (When user program 24 is set to OFF)
10.7 seconds (When user program 24 is set to ON)
Warm-up time * 7
(Approximately)
-
Copy
ratio
Document
glass
Variable: 25% to 400% in 1% increments
(total 376 steps)
Fixed: 50%, 70%, 86%, 100%, 141%, 200%
SPF
Variable: 50% to 200% in 1% increments
(total 151 steps)
Fixed: 50%, 70%, 86%, 100%, 141%, 200%
Exposure
system
Document
glass
Moving optical source, slit exposure (stationary
platen) with automatic exposure
SPF Moving original
Fusing system Heat rollers
Development system Magnetic brush development
Light source Cold cathode fluorescent lamp
Resolution
Copier
600 x 300 dpi (Auto/Manual mode)
600 x 600 dpi (Photo mode)
Printer 600 dpi
Scanner 600 x 600 dpi
Gradation
Scan 256 levels
Output 2 levels
Bit depth 1 bit or 8 bit/pixel
Sensor Colour CCD
Scanning speed Max. 2.88 ms/line
Memory 32 MB
Power supply
Local voltage ±10% (For this machine's power
supply requirement, see the name plate located
on the back of the machine.)
Power consumption Max. 1.0 kW
Overall
dimensions
Width 802 mm
Depth 445 mm
Weight (Approximately) * 8 15.9 kg
Unit
dimensions
Width 518 mm
Depth 445 mm
Height 298 mm
Operating conditions Temperature: 10°C to 30°C
Humidity: 20% to 85%
Emulation
SHARP SPLC
(Sharp Printer Language with Compression)
Interface port USB interface (USB 2.0 Hi Speed)
Noise level
Sound power level L wAd
Copying mode: 6.4 B
Standby mode: 3.5 B
Sound pressure level L pAm (reference) (Bystander positions)
Copying mode: 47 dB
Standby mode: 19 dB
Sound pressure level L pAm (reference) (Operator position)
Copying mode: 52 dB
Standby mode: 19 dB
Noise emission measurement in accordance
with ISO7779.
Acceptable originals
Weight: 56 g/m 2 to 90 g/m 2
Size: A5 to A4
Capacity: Up to 50 sheets
Power supply Drawn from the unit.
Weight
(Approximately)
2.3 kg
Dimensions 496 mm (W) x 359 mm (D) x 89 mm (H)
Paper size A5 to A4
Paper weight 56 g/m 2 to 80 g/m 2
Paper capacity One paper tray with capacity for 250 sheets of
80 g/m 2 paper
Weight 3.0 kg
Dimensions 498 mm (W) x 445 mm (D) x 87 mm (H)
Power supply Drawn from the unit
As a part of our policy of continuous improvement, SHARP
reserves the right to make design and specification changes for
product improvement without prior notice. The performance
specification figures indicated are nominal values of production
units. There may be some deviations from these values in
individual units.
CAUTIONS
Caution label on the unit
The label ( , ) in the fusing area of the unit indicates the following:
: Caution, risk of danger
: Caution, hot surface
Cautions on using
Follow the cautions below when using this unit.
Warning:
• The fusing area is hot. Exercise care in this area when removing misfed
paper.
• Do not look directly at the light source. Doing so may damage your eyes.
Caution:
• Place the unit on a firm, level surface.
• Do not install the unit in a humid or dusty location.
• When the unit is not used for a long time, for example during prolonged
holidays, turn the power switch off and remove the power cord from the
outlet.
• When moving the unit, be sure to turn the power switch off and remove
the power cord from the outlet.
• Do not switch the unit rapidly on and off. After turning the unit off, wait 10
to 15 seconds before turning it back on.
• Do not cover the unit with a dust cover, cloth or plastic film while the power
is on. Doing so may prevent heat radiation, damaging the unit.
• Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
• The socket-outlet shall be installed near the machine and shall be easily
accessible.
Important points when selecting an installation site
Do not install your unit in areas that are:
• damp, humid, or very dusty
• exposed to direct sunlight
• poorly ventilated
• subject to extreme temperature or humidity changes, e.g., near an air
conditioner or heater.
Be sure to allow the required space
around the machine for servicing
and proper ventilation.
Cautions on handling
Be careful in handling the unit as
follows to maintain the performance of
this unit.
Do not drop the unit, subject it to shock or strike it against any object.
Store spare toner cartridges in a cool dry place without removing from
the package before use.
• If they are exposed to direct sunlight or excessive heat, poor copies may
result.
Do not touch the photoconductive drum (green portion).
• Scratches or smudges on the drum will cause dirty copies.
Proper storage
Store the supplies in a location that is:
• clean and dry,
• at a stable temperature,
• not exposed to direct sunlight
Store paper in the wrapper and lying flat.
• Paper stored out of the wrapper or in packages standing on end may curl
or get damp, resulting in paper misfeeds.
Laser information
The products that meet the ENERGY STAR ® guidelines carry the logo
shown above.
The products without the logo may not meet the ENERGY STAR ®
guidelines.
SOFTWARE LICENSE
The SOFTWARE LICENSE will appear when you install the software from
the CD-ROM. By using all or any portion of the software on the CD-ROM or
in the unit, you are agreeing to be bound by the terms of the SOFTWARE
LICENSE.
Trademark acknowledgements
• Microsoft ® , Windows ® , Windows ® 2000, Windows ® XP, Windows Vista ®
and Internet Explorer ® are registered trademarks or trademarks of
Microsoft Corporation in the U.S.A. and other countries.
• Adobe ® , the Adobe ® logo, Acrobat ® , the Adobe ® PDF logo, and Reader TM
are registered trademarks or trademarks of Adobe Systems Incorporated
in the United States and other countries.
• IBM, PC/AT, and PowerPC are trademarks of International Business
Machines Corporation.
• Sharpdesk is a trademark of Sharp Corporation.
• All other trademarks and copyrights are the property of their respective
owners.
Each instruction also covers the optional units used with this product.
CAUTION:
Do not install the machine in a location with poor air circulation.
A small amount of ozone is created inside the machine during printing. The
amount of ozone created is not sufficient to be harmful; however, an
unpleasant odor may be noticed during large copy runs, and thus the machine
should be installed in a room with a ventilation fan or windows that provide
sufficient air circulation. (The odor may occasionally cause headaches.)
* Install the machine so that people are not directly exposed to exhaust from
the machine. If installed near a window, ensure that the machine is not
exposed to direct sunlight.
Supply and Consumables
The supply of spare parts for a repair of the appliance is guaranteed for at least
7 years following the termination of production. Spare parts are those parts of
the apparatus which may break down within the scope of ordinary use of the
product, whereas those parts which normally exceed the life of the product are
not considered spare parts. Consumables also, are available for 7 years
following the termination of production.
20 cm
10 cm 10 cm
Shielded interface cables must be used with this equipment to maintain
compliance with EMC regulations.
Wave length 780 nm+15 nm
-10 nm
Pulse times 12.88 µs ±12.88 ns/7 mm
Output power Max 0.2 mW
At the production line, the output power of the scanner unit is adjusted to
0.18 MILLIWATT PLUS 5% and is maintained constant by the operation
of the Automatic Power Control (APC).
Caution
Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
This Digital Equipment is CLASS 1 LASER PRODUCT (IEC 60825-1
Edition 1.2-2001)
This product is designed for commercial application only and as such it
falls outside the scope of Regulation (EC) 1275/2008 implementing EU
Directive 2005/32/EC on eco-design requirements for standby and off
mode electric power consumption. Sharp does not recommend the
product for domestic application and will not accept any liability for such
use.
Products that have earned the ENERGY STAR ® are
designed to protect the environment through superior
energy efficiency.
Do not make copies of anything which is prohibited from copying by
law. The following items are normally prohibited from copying by
national law. Other items may be prohibited by local law.
Money Stamps Bonds Stocks
Bank drafts Checks Passports Driver's licences
In some areas, the "POWER" switch positions are marked "I" and " " on
the copier instead of "ON" and "OFF".
If your copier is so marked, please read "I" for "ON" and " " for "OFF".
Caution!
For a complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall
be easily accessible.