Pioneer BDP-320 - Manual (Page 60)

07
60
En
Others
Softwa re updating is slow. De pending on the Internet connection and other conditions, some time
may be required to update the software.
• “WRT NG ****” is dis played
on the f ront panel display
du ring software updating.
(**** meaning any
cha
racters)
• “WRT FAILED” is dis played
on the f ront panel display
du ring software updating.
The message is dis played when software updating has failed. Check
again whethe r it can be updated properly.
A message othe r than
“Netwo rk connection test
com pleted successfully” is
dis played when Connection
Test is performed.
Is “LAN cable not connected”
dis
played?
Check that this player and Ethernet hub (or router with hub
functionality) a re properly connected.
• Is “IP add ress cannot be
obtained.” dis played?
• Is “No response from the
gateway.” dis played?
• If the IP add ress is obtained using the DHCP server function, check
the setting is co rrect at the Display Network Configuration
( page 41). For details on the DHCP server function, see the operating
inst ructions of the Ethernet hub (or router with hub functionality).
• Set the IP add ress manually.
Is “IP add ress is overlapped.”
dis played?
• Check the o peration and settings of the DHCP server function of the
Ethe rnet hub (or router with hub functionality). For details on the DHCP
se rver function, see the operating instructions of the Ethernet hub (or
router with hub functionality).
• If this player’s has been set manually, reset the IP address of this
player or other components.
Is the Ethe rnet hub (or router
with hub functionality)
o
perating properly?
• Check the settings and o peration the Ethernet hub (or router with hub
functionality). Fo r details, see the operating instructions of the Ethernet
hub.
• Reboot the Ethe rnet hub (or router with hub functionality).
Problem Check Remedy
The player’s power turns off
automatically.
Is Auto Power Off set to
On?
If Auto Power Off is set to On, the player’s power turns off
automatically if no o peration is performed for over 30 minutes
( page 40).
Is Display Power Off set to
On?
The player’s power may turn off together with the power of the TV
connected to the HDMI OUT terminal. If you do not want the player’s
power to turn off when the TV’s power is turned off, set Display Power
Off to Off (page 38).
The player’s power turns on
automatically.
Is KURO LINK set to On? The player’s power may turn on together with the power of the TV
connected to the HDMI OUT terminal. If you do not want the player’s
power to turn on when the TV’s power is turned on, set KURO LINK to
Off (page 38).
Playe r cannot be operated
with remote control.
Is an AV receiver or amplifier
connected to the CONTROL
IN terminal on the player’s
rear panel?
O perate with the remote control of the device connected to the
CONTROL IN terminal.
A re you operating the remote
cont rol from a point too far
away f rom the player?
O perate from within 7 m of the remote control sensor.
A re the batteries dead? Re place the batteries (page 6).
In put of connected TV, and
AV system and HD AV
Conve
rter switches
automatically.
Is KURO LINK set to On? The in put of the TV, and AV system (AV receiver or amplifier, etc.) and
HD AV Conve rter connected to the HDMI OUT terminal may
automatically switch to the player when playback starts on the player or
the menu sc reen (Home Media Gallery, etc.) is displayed. If you do not
want the in puts of the connected TV, and AV system (AV receiver or
am plifier, etc.) and HD AV Converter to switch automatically, set KURO
LINK to Off (page 38).
“P rocessing failed.” is
dis played.
If the message a ppears repeatedly, please ask your nearest Pioneer
autho rized service center or your dealer to carry out repair work.
Problem Check Remedy
320_VXJ5_IBD_EN.book 60 ページ ２００９年２月２５日 水曜日 午前１０時５７分