Pioneer BDP-320 - Manual (Page 19)

19
En
03
– To listen to audio with the player connected to an
AV receiver or amplifier with an HDMI cable,
connect the TV to the AV receiver or amplifier using
an HDMI cable ( page 15).
• When HDMI or DIGITAL AUDIO is selected at Audio,
linea r PCM audio signals (2 channels) are output
f rom all terminals other than the ones selected at
Audio.
• When ANALOG AUDIO is selected at Audio, no
audio signals a re output from the HDMI OUT or
DIGITAL OUT terminals.
For steps 5 to 7, the step to which you should
proceed depends on the combination of the Video
and Audio settings.
5 Select and set the HDMI High Speed Transmission
setting for the HDMI OUT terminal.
Use
/ to select, then press ENTER.
When HDMI High Speed Transmission for the HDMI
OUT terminal is set to On, use a High Speed HDMI™
cable. The
picture and sound may not be output properly
if any othe r HDMI cable (for example a standard HDMI™
cable) o r an HDMI cable with built-in equalizer is used.
6 Select the output video resolution from the
COMPONENT VIDEO output terminals.
Use
/ to select, then press ENTER.
Fo r details on the resolution settings, see Switching the
output video resolution on page 21.
7 Select the aspect ratio of your TV.
Use / to select, then press ENTER.
8 Check the settings.
Select Proceed, then press ENTER.
9 Output test tones.
Use
/ to select Yes, then press ENTER.
10 Finish the Setup Navigator menu.
Use
/ to select Finish, then press ENTER.
To redo the settings from the start, select Go Back.
De pending on the output terminal setting of step 4 or the
HDMI cable being used, it may ha ppen that no picture
and/o r sound is output. If this happens, the setup returns
to ste p 4 if there is no operation for over 30 seconds. Once
the setu p returns to step 4, redo the settings according to
the connected devices and the HDMI cable being used.
11 Checking the picture quality settings or setting
the picture quality
If a Pionee
r Flat Screen TV or projector is connected to the
player and HDMI is selected for Video in step 4, the
player sets the picture quality automatically. The
automatic
picture quality setting screen appears. Press
ENTER.
When the automatic picture quality setting screen does
not a ppear, the manual picture quality setting screen
a ppears. Use
/ to select the connected component,
then press ENTER.
Operating the TV with
the player’s remote
control
When the manufactu rer code for your brand of TV is set
on the player’s remote control, the TV can be operated
using the player’s remote control.
Caution
• Fo r some models it may not be possible to operate the
TV with the player’s remote control, even for TVs of
b rands listed on the manufacturer code list.
• The setting may be restored to the default after the
batte ries are replaced. If this happens, reset it.
1 Input the 2-digit manufacturer code.
P ress the number buttons (0 to 9) to input the code while
pressing TV CONTROL .
Note
• The facto ry setting is 00 (PIONEER).
• If you make a mistake when in putting the code,
release TV CONTROL  then start over from the
beginning.
• When the re are multiple codes for a manufacturer, try
in putting them in the indicated order until the TV can
be o perated.
2 Check that the TV can be operated.
O perate the TV using TV CONTROL.
 – Press to turn the TV’s power on and off.
INPUT SELECT – Press to switch the TV’s input.
CH +/– – Press to select the TV channel.
VOL +/– – Press to adjust the volume.
TV CONTROL
STANDBY/ON OPEN/CLOSE
AUDIO SUBTITLE ANGLE FL DIMMER
ENTER
INPUT
SELECT CH VOL
AUDIO VIDEO
OUTPUT
RESOLUTION
CLEAR
320_VXJ5_IBD_EN.book 19 ページ ２００９年２月２５日 水曜日 午前１０時５７分