Pioneer DVR-520H-S - Manual (Page 48)

Recording 06
48
En
• If the recorder is stopped, you can also use the +/–
buttons on the front panel to select the channel
number.
3 Use the REC MODE button to set the picture
quality/recording time.
• See Setting the picture quality/recording time on
page 47 for detailed instructions.
4 Use the AUDIO button to select the audio
channel to record.
See Changing audio channels on page 29 for more on
this.
• When recording in VR mode, if a broadcast is
bilingual, both audio channels are recorded, allowing
you to switch the audio channel on playback. The
only exception to this is when the picture quality is set
to
FINE / MN32 , in which case you do need to select
the audio channel before recording.
5 Press ì REC to start recording.
If you want to set a recording end time, press the ì REC
button repeatedly. The recording time increases in 30
minute increments, up to a maximum of six hours. The
time the recording will end is shown on-screen and in the
front panel display. When the recording ends, the
recorder automatically switches into standby if no other
operation is being performed.
• To cancel the set recording time, press
ì REC .
• If you want to pause recording at any time, press
PAUSE . Press again to restart the recording. (If
recording to the HDD or in VR mode, a new chapter
is started after recording restarts)
6 To stop the recording, press STOP REC.
• If you set the recording time in the previous step, you
can still stop the recording anytime by pressing
STOP REC .
• Recording will stop automatically when there is no
more space on the HDD/DVD, or after six hours of
HDD recording (whichever is sooner).
Tip
• During recording you can turn on/off the SCART loop
through function. During recording, press the front
panel
+ button to switch to SCART THRU (loop
through on), or – to switch to SCART NORM (loop
though off). Note that you can’t switch loop through
on if recording from the
AV2/(INPUT 1/DECODER)
or AV1(RGB)-TV connectors. Also, loop through is
automatically reset to off after recording has
finished.
Direct recording from TV
If you connected this recorder to your TV using a SCART
cable, and your TV supports Direct Recording, you can
record whatever is currently being shown on the TV
without having to worry about what channel preset the
recorder is on. Check the instructions that came with
your TV if you’re not sure whether your TV supports this
feature.
1 If necessary, load a recordable disc.
2 Set the picture quality/recording time using the
REC MODE button.
3 Press TV DIRECT REC to start recording.
If you want to set a recording time, press the ì REC
button repeatedly. The recording time increases in 30
minute increments, up to a maximum of six hours. You
can see the recording time on-screen and in the front
panel display. When the recording ends, the recorder
automatically switches into standby if no other operation
is being performed.
• To cancel the set recording time, press
ì REC .
• If you want to pause recording at any time, press
PAUSE . Press again to restart the recording. (If
recording to the HDD or in VR mode, a new chapter
is started after recording restarts)
4 To stop the recording, press STOP REC.
• If you set the recording time in step 3 , you can still
stop the recording anytime by pressing STOP REC .
• Recording will stop automatically when there is no
more space on the HDD/DVD, or after six hours of
HDD recording (whichever is sooner).
Tip
• You can press TV DIRECT REC while the recorder is
in standby to switch on and immediately start
recording.
• Please note that you can’t record from another
component (VCR, etc.) that is connected by a SCART
cable to the
AV2/(INPUT 1/DECODER) connector
using the TV Direct Recording feature.
TV DIRECT
REC
REC
PAUSE
STOP REC REC MODE
ì
DVR-04_HDD_EU.book 48 ページ ２００４年４月１１日 日曜日 午後１時４５分