Pioneer X-HM50-K - Manual (Page 10)

11/2/23 X-HM50_En.fm
10
Setting the clock (Remote control
only) (continued)
5 To adjust the hour, press the or button and
then press the ENTER button. Press the or
button once to advance the time by 1 hour. Hold it
down to advance continuously.
6 To adjust the minutes, press the or button
and then press the ENTER button. Press the or
button once to advance the time by 1 minute.
To confirm the time display:
Press the
CLOCK/TIMER button. The time display will
appear for about 5 seconds.
Note
When power supply is restored after unit is plugged in
again or after a power failure, reset the clock (pages 9 -
10).
To readjust the clock:
Perform “Setting the clock” from step 1. If the “
Clock”
does not appear in step 2, step 4 (for selecting the 24-
hour or 12-hour display) will be skipped.
To change the 24-hour or 12-hour display:
1 Clear all the programmed contents. (Refer to “Factory
reset, clearing all memory” on page 25 for details.)
2 Perform “Setting the clock” from step 1 onwards.
Listening to the iPod or iPhone
Supported iPod and iPhone models:
• iPod touch (1
st /2 nd /3 rd /4 th generation)
• iPod classic
• iPod nano (2
nd /3 rd /4 th /5 th /6 th generation)
• iPhone 4
• iPhone 3GS
• iPhone 3G
• iPhone
Notes
• Audio from the iPod/iPhone cannot be heard via the
headphones connected to the unit.
• Once the iPod or iPhone is connected to the unit it
will begin charging.
• Error message “This accessory is not made to work
with iPhone” may appear on the iPhone screen
when iPhone battery is low.
• The message “This accessory is not made to work
with iPhone” or “This accessory is not supported by
iPhone” may appear on the iPhone screen when the
iPhone is not properly docked (eg. slanting) on this
product. If this occurs, please remove and re-dock
the iPhone.
• To prevent random interference when iPod/
iPhone function is selected, the headphone
output is disabled.
You may also experience brief audio
interference during incoming calls.
Notes
• Please use the adaptor supplied with your iPod or
iPhone unit.
• You can use an audio cable to connect your iPod to
the AUDIO IN socket if:
1. your iPod adaptor does not fit into the iPod dock on
the main unit.
2. you have an iPod that does not have an iPod adaptor.
3. you have an iPod that does not have an iPod 30 pin
connector.
CAUTION
Unplug all accessories from the iPod or iPhone before
inserting it into the dock.
1 Press the STANDBY/ON button to turn the power on.
2 Press the iPod/iPhone button on the remote control
or INPUT button repeatedly on the main unit to
select iPod function.
3 Insert iPod or iPhone unit in iPod dock of main unit.
4 Press the / (iPod/iPhone / ) button to start
playback.
n iPod and iPhone adaptor connection
iPhone
Adaptor No.
iPhone
Description
Capacity
12 iPhone 4GB & 8GB & 16GB
15 iPhone 3G,
iPhone 3GS 8GB & 16GB & 32GB
& 64GB
19 iPhone 4 16GB & 32GB
n To insert iPod or iPhone adaptor
1 Open the iPod cover by pulling up.
2 Insert the iPod or iPhone adaptor into unit and
connect your iPod or iPhone.
n To remove iPod or iPhone adaptor
Insert the tip of a screwdriver (“–”
type, small) into the adaptor hole as
shown and lift upward to remove.
n iPod or iPhone playback
iPhone
Dock connector
iPhone (bottom)
iPhone dock
iPhone connector
iPhone adaptor