Pioneer X-HM71-S - Manual (Page 9)

9
2 2 Connecting your equipment
WLAN antenna connection
Connect the WLAN antenna to the WLAN ANTENNA
terminal.
Please always use the supplied WLAN antenna.
Speaker connection
• The provided speaker wire with the red tube is for the plus
(+) terminal. Connect the wire with red tube to the plus (+)
terminal, and other wire to the minus (–) terminal.
• Use speakers with an impedance of 4 ohms as lower
impedance speakers can damage the receiver.
• The receiver is not magnetically shielded and so should not
be placed near a TV or monitor, as the interaction of
magnetic materials can cause distortion of the colors on
your TV screen. Magnetic storage media (such as floppy
discs and tape or video cassettes) should also not be kept
close to the receiver.
CAUTION
• These speaker terminals carry HAZARDOUS LIVE voltage.
To prevent the risk of electric shock when connecting or
disconnecting the speaker cables, disconnect the power
cord before touching any uninsulated parts.
• Do not mistake the right and the left channels. The right
speaker is the one on the right side when you face the
receiver.
• Do not let the bare speaker wires touch each other.
• Make sure that all the bare speaker wire is twisted together
and inserted fully into the speaker terminal. If any of the
bare speaker wire touches the back panel, it may cause the
power to cut off as a safety measure.
Cleaning the glossy finish of the speaker (X-HM81
only)
• If you use a dusty or hard cloth or if you rub the screen hard,
the finish of the product will be scratched.
• If you clean the surface of the speaker system with a wet
cloth, water droplets on the surface may enter into the
product, resulting in malfunction.
• When cleaning the finish of the speaker system, gently
wipe it with a dry soft cloth.
Applying non skid pads (X-HM81 only)
The use of non skid pads is recommended depending on the
installation location. Apply the pads to the four corners of the
side of the speaker which will be on the bottom. Note that
depending on the location, the pads may not provide fully
sufficient traction to prevent slipping, so care should be taken
not to install the speakers in conditions where they may be
prone to side.
CAUTION
• When applying non skid pads, laid down the speaker on the
soft cloth etc. to avoid working with unstable position.
If not using the provided speaker wire
1
Twist exposed wire strands together.
2
Loosen terminal and insert exposed wire.
3
Tighten terminal.
X-HM81 and X-HM71 only:
• Do not install your speakers overhead on the ceiling or wall.
The grill is designed to be detachable, and as such it may
fall and cause damage or personal injury if installed
overhead.
• Do not allow any objects to fall into or to be placed in the
bass reflex ducts.
• Do not stand or sit on the speakers. You may be injured.
Using other subwoofer
You can connect a subwoofer with an amplifier to the
SUBWOOFER PREOUT socket.
Note
• No sound is heard from the subwoofer without a built-in
amplifier.
Connecting a TV, etc.
Connect to the TV using an audio cable.
Non skid pad
1 2 3
10 mm
PREOUT OUT IN
L
R
AM
LOOP
FM
UNBAL
75Ω
ANTENNA
SPEAKERS WLAN ANTENNA
LINE VIDEO SUBWOOFER
L
R
ADAPTER PORT
Audio cable
(commercially
available)
Audio signal
To audio input
socket
To SUBWOOFER
PREOUT socket
Commercially
available subwoofer
(amplifier built in)
L
R
AM
LOOP
FM
UNBAL
75Ω
ANTENNA
SPEAKERS WLAN ANTENNA
LINE VIDEO SUBWOOFER
L
R
Aud
io sig
na
l
TV
To audio
output sockets
Audio cable
(commercially
available)
To LINE
input
sockets