AZEK InDeck - Manual

Tools Required
Parts
Hardware
• Each AZEK In-Deck Storage Kit comes complete with all hardware, fasten-
ers and installation guide to build one complete unit (i.e. AZEK Deck Boards
must be purchased separately). Check the enclosed Hardware and Parts List
to ensure that the kit is complete.
• AZEK In-Deck Storage should be installed in accordance with the installation
guidelines included below. AZEK Building Products Inc. accepts no liability
or responsibility for the improper installation of this product.
• AZEK In-Deck Storage is designed to be built to the size for which it is
manufactured and should not be altered in any way. It is also designed to be
used with AZEK Deck boards which measure 1” Thick x 5.5” Wide. The lid is
designed to support 500 LBS.
• AZEK In-Deck Storage may not be suitable for every application and it is the
sole responsibility of the installer to be sure that AZEK In-Deck Storage is
used for its intended purpose. Since all installations are unique, it is also the
installer’s responsibility to determine specific requirements in regards to each
In-Deck application.
(4) 1/4-20 x 1 1/4"
Pan Head Machine Screw (18) #10 x 1 3/4" Flat Head
Phillips Wood Screws
(15) #10-32
Nylon Insert
Locking Nut 3/8” (30) #10
Flat Washer (27) #10 x 1 1 / 4 ” Flat Head
Phillips Wood Screws
(4) Shoulder Screws
7/8” L with
5/32” Hex Head (4) 1/4-20 x 1"
Wide Slotted
Machine Screws
(18) 3/8" x 1 3/4" Wood
Lag Screw Hex Head (15) 10-32 x 1 3/4”
Flat Head Phillips Machine Screw
Miter/Chop Saw Circular Saw #2 Phillips
Drive Bit
#3 Phillips
Drive Bit
9/16”
Socket
Flat Head
Screw Driver
Wrench for
Compression Lock
Tape Measure Drive Tool 3/8” Wrench
10mm
3/4”
(1) Trim Ring Lid
(1) Large Bucket
(2) Hinge
Deck Side
(Marked “D”)
(4) Spacer,
Gas Spring
(3) Tub
Support Bracket
(1) Compression
Lock & Pawl Set
(1) Deck Ring
(2) Gas Spring
(1) Lid Frame
(1) Cover
Rain Shield
(1) Handle (2) Hinge Pins (1) Handle
Holder
(2) Hinge
Lid Side
(Marked “L”)
(2) Plugs (2) Vents
IN-DECK STORAGE INSTALLATION GUIDELINES for
Arbor Collection ‰ / Harvest Collection / Terra Collection ‰ Page 1
Spacer Kit
(24) 1/8” Spacers
Tools Provided:
(1) 5/32” Allen Wrench
(2) 1/8” Allen Wrench
• AZEK Building Products recommends that all applications be reviewed by a
licensed architect, engineer, or local building official before installation. Check
local code requirements prior to installation. If you have any questions or
need further assistance, please call AZEK Customer Service at 877-ASK-AZEK
(877-275-2935) or visit our website at www.azek.com.
• IMPORTANT: Make sure the DRIVE TOOL/DRILL is configured or set to
use the SCREW setting when driving and/or tightening all FASTENERS.
Since most screws are designed to seat within the cellular pvc substrate, BE
CAREFUL NOT TO OVERDRIVE, as this may loosen the screw’s holding power.
• SAFETY: Always wear goggles when handling, cutting, drilling and fastening
materials.
• WARNING: In order to avoid tripping due to raised hinge knuckles and lock
reveal, it is a safe practice to install the In-Deck Storage away from heavily
used traffic patterns. When not using the In-Deck Storage, keep it locked in
order to prevent children or others from falling, hiding or becoming enclosed
within the unit.
• WARNING: Lid will not support more than 500 LBS.
Please read all instructions completely before starting any part of the installation.
© 2011 All rights reserved. AZEK Building Products, Inc. www.AZEK.com