AeroBed Elevated Bed with Built-In Pillow - Manual

8076 Rev 4/09
Pump 103H/DTBV Instruction Manual
IMPORTANT SAFETY INFORMATION AND WARNINGS
SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
IMPORTANT : Preparation of your product requires no tools. Use of tools may damage your bed.
WARNING : This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock:
- Unplug from outlet when not in use
- Close supervision is necessary when this product is used by or near children, invalids, or disabled persons.
- Use this product only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water.
- Keep the cord away from heated surfaces.
- Never operate the product with the air openings blocked. Keep the air openings free of lint, hair, and the like.
- Never drop or insert any object into any opening.
WARNING: Product is for indoor use only. For household / residential use only.
WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance.
ADDITIONAL WARNINGS:
- This is not a water toy. Use as a mattress only.
- This bed is not designed for use by children under 3 years of age or any persons with limited mobility as they could suffer serious or fatal injury through suffocation,
falling from or rolling off the bed or becoming trapped.
- Use on flat surfaces only. Bed may tip over on uneven surfaces.
- Inflate bed fully. Partially inflated mattresses can cause suffocation.
- Remove all sharp objects from area where bed will be set up and used. Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters, open
flame, or other hot objects.
- Unplug product when not in use.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time. Do not use pump continuously for more than
4 minutes. To avoid excessive heat build up in the pump, let it rest for 5 minutes between complete inflation and deflation cycles.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside.
Contact Aero Products International, Inc. at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, 1-888-462-4468 for repair or servicing information.
INFLATION
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.
1. Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects.
2. Make certain the Quick Release Valve located at the foot of the bed is closed. If the Air Release Valve is open, close it by using 2 thumbs
to push cover and snap into valve. Be careful to avoid pushing valve cover to the right or left as it snaps into the valve opening.
3. Remove AC pump and cord from protective plastic shipping wraps.
4. Plug into any standard polarized 110 Volt AC electrical outlet. North American Electrical rating: 120 VAC 60HZ 1.0A (Note: 230VAC product
sold outside of North America). This product has a polarized attachment plug (one blade is wider than the other) as a safety feature. This plug
will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Never use with an extension cord unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
5. Remove protective plastic cap from the Quick Air Release Valve by turning counter clockwise. Open the protective rubber cap at the end of
the pump. Press mouth of the pump into position on the Quick Air Release Valve and turn clockwise until it locks.
6. A one-quarter turn clockwise automatically starts inflation.
7. At approximately 3 minutes, a high pitch whine of the pump will signal the bed is inflated to full (firmest) capacity. Bed will not over-inflate.
8. Detach pump by turning counter clockwise. Lie on bed and check the firmness. If you want your bed to be softer, depress the button in the
center of the valve. If the bed becomes too soft, reattach the pump and reinflate the bed until the desired level of firmness is achieved.
IMPORTANT: Be sure to close the protective cap after inflation.
This is the closed position. Open Air Release Valve Close Valve Using 2 Thumbs
DEFLATION AND STORAGE
1. Open the Quick Air Release Valve cover at the foot of the bed to release the air.
2. Fold sides of bed into the center along its length. Tightly roll your bed towards the Quick Air Release Valve at the foot of the bed.
3. Roll the bed completely until all air is expelled. When the bed is completely rolled, push the Quick Air Release Valve closed and lock for its next use.
4. Slide the duffel bag over your AeroBed. Store your bed and pump until its next use.
5. When not in use, store your bed in a clean, dry place out of extreme temperatures.
www.aerobed.com