AeroBed EcoLite - Manual

8101 Rev 3/10
Pump HB177 NiCd/Hi805AB Instruction Manual
IMPORTANT SAFETY INFORMATION AND WARNINGS
SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
IMPORTANT: Preparation of your product requires no tools. Use of tools may damage your bed.
Rechargeable Pump - For outdoor use.
WARNING: The Air Release Valve is made of several small parts which could pose a choking hazard.
Keep all parts away from children under 6 years of age.
WARNING: Pump is not a toy - children must be supervised at all times.
WARNING: Risk of electric shock. Do not expose to rain. Store indoors.
- Pump charger is an electrical device. Do not use in or around water.
- Charger to be used indoors only.
- Do NOT place pump or charger where they could fall or be pulled into the water.
- Not recommended for children under 6 years of age.
- The pump contains nickel-cadmium batteries.
- The pump should not be incinerated.
- The pump should not be overcharged or reverse charged.
- The pump batteries are not replaceable. Do not attempt to replace them.
- Do NOT charge the NiCd battery pump with any other charger than the one provided with the pump.
- Do NOT attempt to dissemble, repair, or service pump. No user serviceable parts are contained inside.
Contact Aero Products International, Inc. at 1834 Walden Office Square, Thrid Floor, Schaumburg, IL 60173,
1-888-462-4468 for repair or servicing information.
WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance.
ADDITIONAL WARNINGS:
- Bed supports a maximum weight of 300 lbs. per person.
- This is not a water toy. Use as a mattress only.
- This bed is not designed for use by children under 3 years of age or any persons with limited mobility as they could suffer
serious or fatal injury through suffocation, falling from or rolling off the bed or becoming trapped.
- Use on flat surfaces only. Bed may tip over on uneven surfaces.
- Inflate bed fully. Partially inflated mattresses can cause suffocation.
- Remove all sharp objects from area where bed will be set up and used. Do not use this bed on abrasive surfaces or near
pointed/sharp items or surfaces. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place
it near or against heaters, open flame, or other hot objects.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time.
Do not use pump continuously (refer to warning statement on side of pump).
To avoid excessive heat build-up in the pump, let it rest for 10 minutes between complete inflation cycles.
A REPAIR PATCH CAN BE ORDERED AT WWW.AEROBED.COM OR BY CALLING OUR CUSTOMER SERVICE AT 1-888-462-4468.
Thank you for joining the AeroBed ® family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed product. You are
about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new AeroBed product.
Always instruct and supervise others on your bed’s proper use, maintenance and safety.
INFLATION
Note: Product must be at room temperature prior to inflating or it may cause air leaks.
1. Place your rolled up bed on the floor or other surface free of obstructions or sharp objects.
2. Remove pump from protective plastic shipping wraps.
3. Open protective cap on valve by turning counter-clockwise (see figure A). Press the side port of the pump into the valve, then turn pump to “on” position
(see figure B).
4. In minutes, your bed will be inflated to the firmest capacity. Detach pump and close valve by turning clockwise.Turn pump to “off” position.
5. Lie on bed and check the firmness. If you want the bed to be firmer, open protective cap by turning counter-clockwise.
Press the side port of the pump into the valve, reinflate the bed until the desired level of firmness is achieved.
6. Replace valve cap.
RECHARGEABLE Ni-Cd PUMP
IMPORTANT: PUMP MUST BE CHARGED FOR 24 HOURS PRIOR TO THE FIRST INFLATION. Use the AC adapter to charge your new Aero pump
for 24 hours. For maximum performance, be sure to fully discharge pump before recharging. After initial charge and use, charge pump for 12 HOURS
at a time. Charging your pump for periods shorter or longer than 12 hours will substantially decrease the life of your Ni-Cd pump. In an emergency, a 3
hour charge will provide one inflation, however, continued charging for 3 hour periods will substantially decrease the life of your Ni-Cd pump.
IMPORTANT: ALWAYS store pump and charger in a cool, dry place. DO NOT allow pump or charger to get wet. Allowing pump and/or charger
to get wet will void your warranty.
TO CHARGE / RECHARGE:
a) First, remove pump and charger from protective plastic shipping wraps.
b) Insert the charger’s mini-plug in the hole.
c) Third, plug the charger unit into any standard 110V (or 220V depending on your local service) electrical outlet and let it charge for 12 hours
(24 hours on initial charge).
NOTE: For best pump performance, you must completely drain the charge from your pump prior to recharging. For directions, see discharge section below.
Prior To Inflation:
a) Unplug the pump after it has been charged for 12 hours (24 hours on initial charge).
b) Remove charger unit from the electrical outlet.
NOTE: Pump will not run while charger is plugged into an electrical outlet.
To Discharge:
a) Place pump on valve as if to inflate product.
b) Allow pump to run until the pump motor dies down.
NOTE: When properly used, your pump will hold a full charge for approximately 90 days. When storing pump for longer than 90 days, fully discharge and
recharge pump every 120 days. This will help maximize pump life.
WARNING: PUMP SHOULD ONLY BE USED WITH AERO ADAPTER PROVIDED. DO NOT USE WITH ANY OTHER ADAPTER.
IMPORTANT: PUMP CONTAINS NICKEL-CADMIUM BATTERIES. BATTERIES MUST BE RECYCLED OR DISPOSED OF PROPERLY.
B
inflation port
A