AeroBed Raised Signature Comfort Airbed - Manual

DEFLATION AND STORAGE
1. There are three ways to deflate your AeroBed; turn the pump to deflate position and let the pump do the work, open the quick air release valve and
let the air flow out or use the pump and valve in combination. Deflation is under one minute.
2. For most compact storage, close valve, turn dial on pump to deflate position. Bed will begin to deflate automatically. Once bed has expelled all air,
turn dial to neutral position.
3. Roll or fold the AC cord and secure it. Fold sides of bed into the center along its length. Tightly roll and place in convenient
carry bag for easy transport and storage.
4. Store your AeroBed in a clean, dry place at room temperature (above 50°F/10°C). Storing your AeroBed under 50°F (10°C)
and over 100°F (38°C) may affect its performance and will not be covered under warranty.
8109 Rev 9/09
Pump 3111RFI NW F2/DV Instruction Manual
This is the closed position. Open Air Release Valve Close Valve Using 2 Thumbs
INFLATION
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.
Remove your AeroBed from its lightweight duffle bag. Keep bag for storage.
1. Place your rolled-up bed on the floor free of obstructions or sharp objects.
2. Make certain the Quick Release Valve is closed. Bed should be stored with valve in the closed and latched
position. If the Quick Release Valve is open, close it by using 2 thumbs to push cover and snap into valve. Be careful to avoid
pushing valve cover to the right or left as it snaps into the valve opening.
3. Remove AC plug and cord from plastic bag and shrink wrap.
4. Plug into any standard polarized 110 Volt AC electrical outlet. North American Electrical rating: 120 VAC 60HZ 1.10A (Note: 230VAC product
sold outside of North America). This product has a polarized attachment plug (one blade is wider than the other) as a safety feature. This plug
will fit into a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Never use with an extension cord unless the plug can be fully inserted. Do not attempt to defeat this safety feature.
5. Turn dial on pump to “inflate” position. Bed will inflate hands-free. When desired firmness is reached, turn dial to neutral position.
6. To adjust firmness level, slowly turn dial on pump to adjust position. Pump will slowly release air. Turn pump to neutral position once you reach
your desired firmness level. To add more air, repeat step 5.
IMPORTANT: PUMP HAS POWER INDICATOR LIGHT AND RESETTABLE FUSE WITH AUTO SHUT-OFF FEATURE. IF PUMP RUNS FOR
APPROXIMATELY 15 CONSECUTIVE MINUTES, THE AUTO SHUT-OFF FEATURE WILL ENGAGE TURNING THE PUMP OFF. THE PUMP WILL
RESET ITSELF WITHIN 30 MINUTES ONCE THE MOTOR IS COOL. THE POWER INDICATOR LIGHT WILL REMAIN ON AS LONG AS THE BED
IS PLUGGED INTO THE ELECTRICAL OUTLET.
DEFLATE
INFLATE
SILENT ADJUST
POWER INDICATOR
Thank you for joining the AeroBed ® family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed product.
You are about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new
AeroBed product. Always instruct and supervise others on your bed’s proper use, maintenance and safety.
IMPORTANT SAFETY INFORMATION AND WARNINGS
SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
IMPORTANT: Preparation of your product requires no tools. Use of tools may damage your bed.
WARNING: This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock:
- Always unplug from outlet when not in use and before cleaning.
- Close supervision is necessary when this product is used by or near children, invalids, or disabled persons.
- Use this product only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or damaged, or dropped into water.
- Keep the cord away from heated surfaces.
- Never operate the product with the air openings blocked. Keep the air openings free of lint, hair, and the like.
- Never drop or insert any object into any opening.
- To disconnect, turn all controls to off position, then remove plug from outlet.
WARNING: Product is for indoor use only. Do not use outdoors. For household / residential use only.
WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance.
ADDITIONAL WARNINGS:
- Bed supports a maximum weight of 300 lbs. per person.
- This is not a water toy. Use as a mattress only.
- This bed is not designed for use by children under 3 years of age or any persons with limited mobility as they could suffer serious or fatal injury through suffocation, falling from
or rolling off the bed or becoming trapped.
- Use on flat surfaces only. Bed may tip over on uneven surfaces.
- Inflate bed fully. Partially inflated mattresses can cause suffocation.
- Remove all sharp objects from area where bed will be set up and used. Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters,
open flame, or other hot objects.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time. Do not use pump continuously
for more than 4 minutes. To avoid excessive heat build-up in the pump, let it rest for 5 minutes between complete inflation cycles.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside.
Contact Aero Products International, Inc. at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, 1-888-462-4468
for repair or servicing information.
A REPAIR PATCH CAN BE ORDERED AT WWW.AEROBED.COM OR BY CALLING OUR CUSTOMER SERVICE AT 1-888-462-4468.