AeroBed Elevated Home and Camp - Manual

8095 Rev 12/09
Pump 132RV Instruction Manual
INFLATION
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY CAUSE AIR LEAKS.
1. Place your unrolled bed on the floor or other surface free of obstructions or sharp objects.
2. Before inflation, make sure flapper inside valve is closed (see figure A). If not, pull red bar firmly to close. Then,
twist valve cover securely on (see figure B).
3. Click button on pump to “on” ( - ) position. Bed will begin to inflate automatically. When desired firmness is reached,
click button to “off” ( o ) position (figure F). A high pitch whine of the pump will signal when the bed is inflated to the full (firmest)
capacity. Bed will not over-inflate.
4. Lie on bed and check the firmness. If you want your bed to be softer, press the rubber flap inside the valve (see figure C).
A REPAIR PATCH CAN BE ORDERED AT WWW.AEROBED.COM OR BY CALLING OUR CUSTOMER SERVICE AT 1-888-462-4468.
Thank you for joining the AeroBed ® family by purchasing one of our products. You can expect top-notch quality, innovation and imagination from every AeroBed product.
You are about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new
AeroBed product. Always instruct and supervise others on your bed’s proper use, maintenance and safety.
IMPORTANT SAFETY INFORMATION AND WARNINGS
SAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
IMPORTANT: Preparation of your AeroBed product requires no tools. Use of tools may damage your bed.
WARNING: This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock:
- Close supervision is necessary when this product is used by or near children, invalids, or disabled persons.
- Use this product only for its intended use as described in these instructions. Do not use attachments not recommended by the manufacturer.
- Never operate this product if it is not working properly, if it has been dropped or damaged, or dropped into water.
- Never operate the product with the air openings blocked. Keep the air openings free of lint, hair, and the like.
- Never drop or insert any object into any opening.
WARNING: Product is for indoor use only. For household / residential use only.
WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance.
ADDITIONAL WARNINGS:
- Bed supports a maximum weight of Twin 350 lbs., Full 450 lbs., Queen 600 lbs.
- This is not a water toy. Use as a mattress only.
- This bed is not designed for use by children under 3 years of age or any persons with limited mobility as they could suffer serious or
fatal injury through suffocation, falling from or rolling off the bed or becoming trapped.
- Use on flat surfaces only. Bed may tip over on uneven surfaces.
- Inflate bed fully. Partially inflated mattresses can cause suffocation.
- Remove all sharp objects from area where bed will be set up and used. Do not use this bed on abrasive surfaces or near
pointed/sharp items or surfaces. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it
near or against heaters, open flame, or other hot objects.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside. Contact Aero Products
International, Inc. at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, 1-888-462-4468 for repair or servicing
information.
Tap red bar gently for
desired firmness
C
Pull red bar firmly to close
flapper valve
A
Twist valve cover back on
B
Deflating – Push flapper
valve open into locked
position
D
Inserting D-Cell batteries:
a) Remove protective plastic shipping wrap from pump.
b) Open battery cover located on the front of the pump. NOTE: Cap is attached on one side of pump; Do NOT pull completely off pump.
c) Insert four new D-cell alkaline batteries (NOT INCLUDED). Make certain the batteries are installed correctly (see figure E).
d) Replace battery cover.
BATTERIES MUST BE RECYCLED OR DISPOSED OF PROPERLY.
TO REACH MAXIMUM FIRMNESS AND EXTEND BATTERY LIFE:
G
DEFLATION AND STORAGE
1. Open the Rapid Release valve cover and press the rubber flapper inside the valve to the locked open position to release the air
(see figure D).
2. Fold sides of bed into the center along its length (see figure G). Tightly roll your bed towards the valve.
3. Roll the bed completely until all air is expelled. When the bed is completely rolled, turn valve cap clockwise until it is locked in
place. Slide the duffel over your AeroBed and store for its next use.
4. Store your AeroBed in a clean, dry place at room temperature (above 50°F/10°C). Storing your AeroBed under 50°F (10°C)
and over 100°F (38°C) may affect its performance and will not be covered under warranty.
E
on off
F
9” Twin
9” Queen
12” Queen 12” Twin
2 minutes
2 minutes
1 minute Inflate for:
Rest pump for:
Inflate again for: 3 minutes
2 minutes
1 minute 5 minutes
2 minutes
2 minutes