AeroBed Premier Cushioned Comfort - Manual

DEFLATION AND STORAGE
1. To deflate your AeroBed, open the Quick Air Release Valve. Deflation takes
approximately 60 seconds.
2. For most compact storage, close valve and follow quick start guide.
DO NOT INTERRUPT DEFLATION, PUMP WILL AUTOMATICALLY SHUT
ITSELF OFF.
3. Roll or fold the AC cord with wand control and secure it. Fold sides of bed into the
center along its length. Tightly roll and place bed in convenient carry bag for easy
storage and transport.
4. Store your AeroBed in a clean, dry place at room temperature (above 50°F/10°C). Storing
your AeroBed under 50°F (10°C) and over 100°F (38°C) may affect its performance and
transport.
Thank you for joining the AeroBed ® family by purchasing one of our upscale products. You can expect top-notch quality, innovation, and imagination from every AeroBed product.
You are about to enjoy the comfort of an AeroBed product. It is your responsibility to read and always follow the safety, care and maintenance instructions for your new AeroBed
product. Always instruct and supervise others on your bed’s proper use, maintenance and safety.
IMPORTANT: Preparation of your AeroBed product requires no tools. Use of tools may damage your bed.
7993 Rev 11/09
Pump 120/DV Instruction Manual
IMPORTANT SAFETY INFORMATION AND WARNINGS
WARNING: Adult supervision required for inflation, deflation, and maintenance. Follow all safety instructions to avoid serious injury.
WARNING: This is an electrical product – not a toy. To avoid risk of fire, burns, injury, or shock, it should not be played with or placed where children can reach it. Do not use
in or around water.
WARNING: Product is for indoor use only.
WARNING: For household / residential use only.
WARNING: This furnishing has not been evaluated for flammability or cigarette ignition resistance
- Close supervision is necessary when this product is used by or near children, invalids, or disabled persons.
- This is not a water toy. Use as a mattress only.
- This mattress is not intended for infants or persons with limited mobility. They may roll off of the mattress and become entrapped between the mattress and a wall.
- Remove all sharp objects from area where bed will be set up and used. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- Place bed in a safe area before use, making sure that there are no sharp edges, steps, drops, or breakable items nearby. Use on flat surfaces only.
Bed may tip over on uneven surfaces.
- Do not use this bed on abrasive surfaces or near pointed/sharp items or surfaces. Protruding objects may puncture the bed.
- This bed is made of plastic and therefore may melt or burn if it comes in contact with any flame or heat source. Do not place it near or against heaters, open flame, or other hot
objects.
- Unplug product when not in use.
- Pump is not intended for continuous use. Pump may stop working or overheat if it is used for extended periods of time.
Do not use pump continuously for more than 10 minutes. To avoid excessive heat build up in the pump, let it rest for 5 minutes between complete inflation and deflation cycles.
- Do not attempt to disassemble, repair, or service the pump. No serviceable parts are contained inside. Contact Aero Products International, Inc.
at 1834 Walden Office Square, Third Floor, Schaumburg, IL 60173, for repair or servicing information.
INFLATION
NOTE: BED MUST BE AT ROOM TEMPERATURE PRIOR TO INFLATING OR IT MAY
CAUSE AIR LEAKS
Remove your AeroBed from its lightweight duffle bag. Keep bag for storage.
1. Place your rolled-up bed on the floor free of obstructions or sharp objects.
2. Make certain the Quick Release Valve located next to pump is closed. Bed should be
stored with valve in the closed and latched position. If the Quick Release Valve is open,
close it by using 2 thumbs to push cover and snap into valve. Be careful to avoid
pushing valve cover to the right or left as it snaps into the valve opening.
3. Remove AC plug, cord, and control wand from plastic bag and shrink wrap.
4. Plug into any standard polarized 110 Volt AC electrical outlet. North American Electrical
rating: 120 VAC 60HZ 1.0A (Note: 230VAC product sold outside of North America). This
product has a polarized attachment plug (one blade is wider than the other) as a safety
feature. This plug will fit into a polarized outlet only one way. If the plug does not fit
fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Never use with an extension cord unless the plug can be fully inserted.
Do not attempt to defeat this safety feature.
5. To inflate, follow Quick Start Guide. DO NOT INTERRUPT INFLATION, PUMP WILL
AUTOMATICALLY SHUT ITSELF OFF.
CAUTION: Do not sleep on edges of the bed. Edges are less supportive and may crush
under weight.
95
27 5/
08
quick
star
t
guide
inflate Always fully inflate mattress
before adjusting firmness level:
1
2
Press Inflate on pump : Pump will stop
automatically when bed fully inflates. (DO NOT
INTERRUPT INFLATION. If inflation is interrupted, press
inflate again to continue cycle.)
Use Control Wand to adjust firmness.
(Firmer/Softer)
1 2
quick
star
t
guide
deflate For automatic deflation:
1
For Quick-Air Release:
1. Open the Whoosh valve and
allow air to expel
2. Close valve
3. Press deflate on pump
(Do not interrupt deflation. Pump
will auto stop when fully deflated.)
Quick Tip!
1 Press Deflate on pump
Pump will stop automatically when bed
is fully deflated.
(Do not interrupt deflation.)
A REPAIR PATCH CAN BE ORDERED AT WWW.AEROBED.COM OR BY CALLING OUR CUSTOMER SERVICE AT 1-888-462-4468.