Kenwood C-414-W - Manual (Page 12)

22
C-414 English
23
In case of diffi culty
Cannot play.
\ Check if the USB mass storage class compatible
digital audio player is turned ON.
iPod/iPhone operation
"NO iPod" is displayed.
\ Insert the iPod/iPhone properly.
Does not function properly.
\ Disconnect the iPod/iPhone and connect it
again.
\ Check the software version of the iPod/iPhone.
If it is not the latest one, update it.
SD operation
"NO SD" is displayed.
\ Press button again after press button.
\ Insert the SD card properly.
"NOT SUPPORT" is displayed.
\ Press button again after press button.
Cannot play.
\ Insert an SD card containing music fi les.
D.AUDIO operation
Kenwood digital audio player cannot be
controlled from the main unit or remote control
unit.
\ Connect using the connection cable
(separately available).
\ Check if a compatible model is connected.
Radio reception
Noise in radio.
\ Tune to a correct frequency.
\ Adjust the direction of the FM antenna.
\ Adjust the position and direction of the AM
antenna.
\ Increase the distance between the system and
TV or VCR.
Remote control unit
Does not function properly.
\ Replace the batteries.
\ Remove the obstacles.
\ Move closer to the system when using the
remote control and make sure that you are
pointing at unit’s remote sensor.
Resetting the Microcomputer
The microcomputer may malfunction (unit cannot be
operated, or shows an erroneous display) if the power
cord is unplugged while the power is ON, or due to
some other external factor. If this happens, execute
the following procedure to reset the microcomputer
and return the unit to its normal operating condition.
When the power is off (standby mode), press the
[SOUND] button on the main unit until "FACTORY
RESET " appears.
Unplug the AC cord and plug it back in if "RESET
FINISHED" appears.
• Please note that resetting the microcomputer will clear the
contents of the memory and return the unit to the state it
was in when it left the factory.
Check that following guide for problem resolution.
General
No sound.
\ Plug in AC cord securely.
\ Set the VOLUME control to proper sound level.
\ Make sure the source is set to the source you
want to operate.
\ Pull out the headphones plug from the
headphones jack.
The left and right sound outputs are reverse.
\ Check the speaker connections and location.
The system does not operate by pressing any
buttons.
\ Unplug the AC cord and plug it back in.
This unit is turned OFF spontaneously.
\ A.P.S. is set to ON. Set it to OFF.
CD player operation
"NO DISC" is displayed.
\ Insert a disc correctly (label side up).
\ Clean the disc.
\ Use a new or readable disc.
\ Wait until the moisture condensation at the
lens has cleared.
USB operation
"NO USB" is displayed.
\ Press button again after press button.
\ Insert the USB device properly.
"NOT SUPPORT" is displayed.
\ Press button again after press button.
General information
Maintenance
Cleaning the cabinet
• Use a soft cloth slightly moistened with a mild detergent
solution. Do not use a solution containing alcohol, spirits,
ammonia or abrasive.
Cleaning discs
• When a disc becomes dirty, clean it with a cleaning cloth,
wipe the disc from the center out. Do not wipe in circular
motion.
• Do not use solvents such as benzene, thinner commercially
available cleaners, or antistatic spray intended for analogue
records.
Caution on condensation
Condensation (of dew) may occur inside the unit
when there is a great diff erence in temperature
between this unit and the outside. This unit may
not function properly if condensation occurs. In this
case, leave the unit for a few hours and restart the
operation after the condensation has dried up.
Be specially cautious against condensation in the
following circumstances:
When this unit is carried from one place to another
across a large diff erence in temperature, when the
humidity in the room where this unit is installed
increases, etc.
To install speakers on a wall
Prepare commercially available wood screws.
9 mm
16 mm
1 On a stable pillar or wall, attach a pair of wood
screws at the same interval as the interval
between the wall-mount holes of speaker.
Screw attaching interval
Speaker: 90 mm
4 mm
2 Fit the screws into the wall-mount holes on the
rear of the speaker.
¤ CAUTION
Be sure to observe the following points when installing the
unit on a wall. Otherwise, the product may drop and cause
damage or an injury.
• Check the strength of the wall before installation. Do not
install on a plywood or plaster board. If you have any doubt
related to the wall strength, please consult a specialist.
• Check that the screws are fit securely into the wall-mount
holes of the speakers.
• Even after installation, use care so that the speakers do not
drop due to an accidental contact, etc.
Information on Disposal of Old Electrical and
Electronic Equipment and Batteries (applicable
for EU countries that have adopted separate
waste collection systems)
Products and batteries with the symbol
(crossed-out wheeled bin) cannot be disposed
as household waste.
Old electrical and electronic equipment and
batteries should be recycled at a facility capable
of handling these items and their waste
byproducts.
Contact your local authority for details in
locating a recycle facility nearest to you.
Proper recycling and waste disposal will help
conserve resources whilst preventing
detrimental effects on our health and the
environment.
Notice: The sign "Pb" below the symbol for
batteries indicates that this battery
contains lead.