Siemens EH801FM17E - Manual (Page 6)

en
Ú Installation instructions
Important notes
Safety: Safety in use is only guaranteed if the technical
installation of the hob has been carried out correctly and in
accordance with the assembly instructions. The installation
technician shall be liable for any damage caused as a result of
unsuitable installation.
Electric connection: Only by an authorised specialist
technician. The guidelines set out by the local electricity provider
must be observed.
Type of connection: The appliance falls under protection class I
and can only be used in combination with a grounding
conductor connection.
The manufacturer accepts no responsibility for any malfunction
or damage caused by incorrect electrical installations.
Installation: The appliance must be connected to a fixed
installation and the means of disconnecting it from the fixed
installation must be installed according to the installation
instructions.
Built-in assembly under worktop: The induction hobs may only
be installed over a drawer, ovens with forced ventilation from the
same brand and dishwashers from the same brand.
Refrigerators, unventilated ovens and washing machines may
not be installed beneath the hob.
Power cable: Do not tie the power cable or pass it along sharp
edges. If there is an oven installed below, pass the cable along
the rear corners of the oven to the connection box. It must be
positioned so that it does not touch any of the hot parts of the
hob or the oven.
Hob: flat, horizontal, stable. Follow the hob manufacturer's
instructions.
Warranty: an unsuitable installation, connection or assembly will
invalidate the product warranty.
Note: Any change to the appliance's interior, including changing
the power cable, must only be performed by specially trained
members of the Technical Assistance Service.
Preparation of assembly units, figures 1/2/3/4/5
Built-in kitchen units: Minimum temperature resistance of
90°C.
Gap: Remove any shavings after performing cutting work.
Cut surfaces: Seal with heat resistant material.
The appliance can be mounted on the following heat and water
resistant worktops:
■
Marble, natural stone worktops
■
Synthetic worktops
■
Solid wood worktops: only according to the manufacturer of
the worktop (sealing of cutout edges)
■
Assembly with other types of worktops: only according to the
manufacturer of the worktop
Note: All worktop cutout work must be carried out by a
specialised service according to the assembly drawings. The
cutout must be clean and precise, as the cut edge will be visible
on the surface. Clean and degrease the cutout edges using a
suitable cleaning product (check the silicone manufacturer's
indications).
Assembly over drawer, figure 2a
Metal objects stored inside the drawer could become very hot
due to the air recirculating from the hob ventilation system. If
this occurs, an intermediate support is recommended.
Intermediate support: A wooden panel can be used (figure 3) or
you may order a suitable accessory from our Technical
Assistance Service. The reference code for this accessory
is 687888.
Hob: must have a minimum thickness of 30 mm.
The distance between the top of the hob and the top of the
drawer must be 70 mm.
Assembly over oven, figure 2b
Hob: must have a minimum thickness of 30 mm.
Note: If the distance between the hob and oven must be
increased, refer to the installation instructions for the oven.
Ventilation: The distance between the oven and the hob must be
at least 5 mm.
Installation above the dishwasher
An intermediate accessory must be installed. The accessory
may be ordered from our Technical Assistance Service. The
reference code for this accessory is 687888.
Hob: must have a minimum thickness of 30 mm and a
maximum thickness of 40 mm.
The space between the top of the hob and the top of the
dishwasher must be:
■
65 mm if installed over a compact dishwasher.
■
70 mm if installed over a full-size dishwasher.
Ventilation, figure 4
Ventilating the hob requires:
■
An opening on the upper part of the kitchen unit's rear wall
(figure 4a).
■
A separation between the rear part of the kitchen unit and
kitchen wall (figure 4b).
■
If the interior width of the kitchen unit is less than 750 mm, a
cut must be made in the side walls (figure 4c).
Adhesive seal, figure 5:
Adhere the adhesive seal to the stepped rim of the worktop.
Installing the appliance, figures 6/7/8
Note: Wear protective gloves to fit the hob. The non-visible
surfaces may have sharp edges.
1. Insert the appliance uniformly in the cutout.
2. Check that the hob is flush with the worktop. If the hob is not
flush, install the anchoring devices supplied and tighten them
carefully, (figure 6).
Note: Do not use electric screwdrivers.
3. Connect the appliance to the mains and check that it works
correctly.
– See the rating plate for the voltage.
– Only connect the appliance in accordance with the
connection diagram (Fig. 8).
1. Brown
2. Black
3. Blue
4. Grey
5. Green-yellow
Note: Depending on the type of connection, the arrangement of
the clamps supplied by the factory may need to be changed.
4. Before sealing the joint (figure 7) you must test that the
appliance works!
Grout the perimeter separation using appropriate, heat
resistant silicone ( e.g. Novasil ® S70, Ottoseal ® S70). Smooth
the seal with a finishing product recommended by the
manufacturer. Follow the silicone indications. Do not start the
appliance until the silicone is completely dry (minimum
24 hours, depending on the ambient temperature).
The appropriate silicones can be obtained through our
Technical Assistance Service.
Caution!
The use of unsuitable silicone causes permanent colour
changes to natural marble worktops.
Uninstalling the appliance
Disconnect the appliance from the mains.
Remove the silicone seal from the edge of the hob with a
suitable tool.
Remove the anchoring devices.
Push the hob upwards from below to remove it.
Caution!
Damage to the appliance! Do not try to remove the appliance by
pulling it from above.