Notifier Dual Voltage Evacuation Speakers - Manual (Page 2)

Page 2 of 2 — DN-60327:B1 • 11/9/11
SpectrAlert® is a registered trademark of Honeywell International Inc.
©2011 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com
Made in the U.S. A.
Architectural/Engineering
Specifications
GENERAL
SpectrAlert Advance speaker and speaker strobes shall mount to a
4” x 4” x 2-1/8” backbox. A universal mounting plate shall be used for
mounting ceiling and wall products. The notification appliance circuit and
amplifier wiring shall terminate at the universal mounting plate. Also,
SpectrAlert Advance speaker strobes, when used with the Sync Circuit.
Module accessory, shall be powered from a non-coded notification appli-
ance circuit output and shall operate on a nominal 12 or 24volts. When
used with the Sync.Circuit Module, 12 volt rated notification appliance cir-
cuit outputs shall operate between nine and 17.5 volts; 24 volt rated notifi-
cation appliance circuit outputs shall operate between 17 and 33 volts.
Indoor SpectrAlert Advance products shall operate between 32°F and
120°F from a regulated DC, or full-wave rectified, unfiltered power supply.
Speaker strobes shall have field-selectable candela settings including 15,
15/75, 30, 75, 95, 110, 115, 135, 150, 177, 185.
SPEAKER
The speaker shall be a System Sensor SpectrAlert Advance model
_______ dual-voltage transformer speaker capable of operating at 25.0 or
70.7 nominal Vrms. It should be listed to UL/ULC 1480 and shall be
approved for fire protective service. The speaker shall have a frequency
range of 400 to 4000Hz and shall have an operating temperature between
32°F and 120°F. Speaker shall have power taps and voltage that are
selected by rotary switches.
SPEAKER STROBE COMBINATION
The speaker strobe shall be a System Sensor SpectrAlert Advance model
__________ listed to UL1480 and UL/ULC 1971 and be approved for fire
protective signaling systems. Speaker shall be capable of operating at
25.0 or 70.7 nominal Vrms selected via rotary switch, and shall have a fre-
quency range of 400 to 4000Hz. Speaker shall have power taps which are
selected by rotary switch. The strobe shall comply with the NFPA 72
requirements for visible signaling appliances, flashing at 1Hz over the
strobe’s entire operating voltage range. The strobe light shall consist of a
xenon flash tube and associated lens/reflector system.
SYNCHRONIZATION MODULE
The module shall be a System Sensor Sync Circuit model MDL listed to
UL/ULC 464 and shall be approved for fire protective service. The module
shall synchronize SpectrAlert strobes at 1Hz. The module shall mount to a
4-11/16” x 4-11/16” x 2-1/8” backbox. The module shall also control two
Style Y (class B) circuits or one Style Z (class A) circuit. The module shall
synchronize multiple zones. Daisy chaining two or more synchronization
modules together will synchronize all the zones they control. The module
shall not operate on a coded power supply.
Ordering Information
NOTE: (W) indicates white coloring; (R), red.
NOTE: “A” suffix indicates ULC-Listed model.
WALL MOUNT
SP(W)(R)(A): Speaker only.
SP(W)(R)V(A): Speaker only, high dB; white.
SPS(W)(R)(A)*: Speaker strobe, selectable candela (15, 15/75,
30, 75, 95, 110, 115).
SPS(W)(R)H(A)*: Speaker strobe, selectable candela, high cd
(135, 150, 177, 185).
SPS(W)(R)V(A)*: Speaker strobe, selectable candela, high dB.
CEILING MOUNT
SPC(W)(R)(A): Speaker only.
SPC(W)(R)V(A): Speaker only, high dB.
SPSC(W*)(R)(A): Speaker strobe, selectable candela (15, 15/
75, 30, 50, 75, 95, 110, 115)
SPSC(W*)(R)H(A): Speaker strobe, selectable candela, high
cd (135, 150, 177, 185)
SPSC(W*)(R)V(A): Speaker strobe, selectable candela, high
dB (15, 15/75, 30, 50, 75, 95, 110, 115).
SPSC(W*)(R)VH(A): Speaker strobe, selectable candela, high
dB, high cd (135, 150, 177, 185).
ACCESSORIES
RFP(A): Retrofit plate (5 pack), red.
RFPW(A): Retrofit plate (5 pack), white.
SPBBSC(A): Ceiling mount backbox skirt, red.
SPBBSCW(A): Ceiling mount backbox skirt, white.
SPBBS(A): Wall mount backbox skirt, red.
SPBBSW(A): Wall mount backbox skirt, white.
TR(A): Wall mount trim ring, red, package of 5.
TRW(A): Wall mount trim ring, white, package of 5.
TRC(A): Ceiling mount trim ring, red, package of 5.
TRCW(A): Ceiling mount trim ring, white, package of 5.
MWBB(A): Wall mount, metal weatherproof backbox
MWBBW(A): Wall mount, metal weatherproof backbox, white
MWBBC(A): Ceiling mount, metal weatherproof backbox
MWBBCW(A): Ceiling mount, metal weatherproof backbox,
white
*NOTE: Add -P to model number for plain housing (no ‘FIRE’
marking on the cover), e.g. SPSW-P
UL Maximum Strobe Current Draw (mA RMS)
Candela
8 to 17.5 Volts 16 to 33 Volts
DC FWR DC FWR
Standard
Candela
Range
15 123 128 66 71
15/75 142 148 77 81
30 NA NA 94 96
75 NA NA 158 153
95 NA NA 181 176
110 NA NA 202 195
115 NA NA 210 205
High
Candela
Range
135 NA NA 228 207
150 NA NA 246 220
177 NA NA 281 251
185 NA NA 286 258
Sound Output
UL Reverberant (dBA @ 10ft) 2W 1W ½W ¼W
Wall Mount SP Series 86 83 80 77
Wall Mount SPV Series 90 87 84 81
Ceiling Mount SPC Series 86 83 80 77
Ceiling Mount SPCV Series 90 87 84 81
Wall Mount SPS Series 85 82 79 76
Wall Mount SPSV Series 89 86 83 80
Ceiling Mount SPSC Series 85 82 79 76
Ceiling Mount SPSCV Series 89 86 83 80