Notifier FAPT-851 - Manual (Page 2)

Page 2 of 2 — DN-6937:D • 12/07/2011
Notifier®, ONYX®, FlashScan®, and Acclimate® are registered trademarks
and Acclimate Plus™ is a trademark of Honeywell International Inc.
©2011 by Honeywell International Inc. All rights reserved. Unauthorized use
of this document is strictly prohibited.
This document is not intended to be used for installation purposes.
We try to keep our product information up-to-date and accurate.
We cannot cover all specific applications or anticipate all requirements.
All specifications are subject to change without notice.
For more information, contact Notifier. Phone: (203) 484-7161, FAX: (203) 484-7118.
www.notifier.com
Made in the U.S. A.
• 4.0" (10.16 cm) square box.
• 3.5" (8.89 cm) or 4.0" (10.16 cm) octagonal box.
• Single-gang box (except relay or isolator base).
NOTE: The FAPT-851(A) detector has the unique ability to adjust
sensitivity according to the environment, based on heat and
smoke levels. Avoid installing these detectors in locations that are
susceptible to rapid and high temperature changes. An example of
an incorrect application would be near or in line with the output of a
self-contained heater.
Agency Listings and Approvals
These listings and approvals apply to the modules specified in
this. In some cases, certain modules or applications may not
be listed by certain approval agencies, or listing may be in pro-
cess. Consult factory for latest listing status.
•
UL Listed: S1115.
• ULC Listed: S1115.
• MEA Listed: 225-02-E.
• FM Approved.
•
CSFM: 7272-0028:0206.
• U.S. Coast Guard: 161.002/42/1 (NFS-640); 161.002/50/0
(NFS2-640/NFS-320/NFS-320C, excluding B210LP(A)).
• Lloyd’s Register: 11/600013 (NFS2-640, NFS-320/NFS-
320C, excluding B210LP(A)).
• Maryland State Fire Marshal: Permit # 2122.
Ordering Information
NOTE: “A” suffix indicates ULC Listed model.
FAPT-851: Low-profile intelligent multi-sensor detector.
FAPT-851A: Same as FAPT-851 but with ULC Listing.
INTELLIGENT BASES
NOTE: “A” suffix indicates ULC Listed model.
NOTE: For details about intelligent bases and their mounting, see
DN-60054.
B210LP (A) : Plug-in detector base; standard U.S. flanged low-
profile mounting base.
B210LPBP: Bulk pack of B210LP; package contains 10.
B501(A): Flangeless mounting base.
B501BP: Bulk pack of B501; package contains 10.
B200S
(A) : Intelligent, programmable sounder base capable of
producing sound output in high or low volume with ANSI Tem-
poral 3, ANSI Temporal 4, continuous tone, marching tone,
and custom tone.
B200SR
(A) : Intelligent sounder base capable of producing
sound output with ANSI Temporal 3 or continuous tone.
Replaces B501BH series bases in retrofit applications.
B224RB
(A) : Relay base Screw terminals: up to 14 AWG (2.0
mm²). Relay type Form-C. Rating: 2.0 A @ 30 VDC resistive;
0.3 A @ 110 VDC inductive; 1.0 A @ 30 VDC inductive.
B224BI
(A) : Isolator base. Maximum: 25 devices between iso-
lator bases.
ACCESSORIES
F110: Retrofit flange to convert B210LP to match the B710LP
profile, or to convert older high-profile bases to low-profile.
F110BP: Bulk pack of F110; package contains 15.
F210: Replacement flange for B210LP(A) base.
RA100Z(A): Remote LED annunciator. 3 – 32 VDC. Fits U.S.
single-gang electrical box. Supported by B210LP(A) and
B501(A) bases only.
SMB600: Surface mounting kit for use with B210LP(A).
M02-04-00: Test magnet.
M02-09-00: Test magnet with telescoping handle.
XR2B: Detector removal tool. Allows installation and/or
removal of FlashScan® Series detector heads from base in
high ceiling installations.
T55-127-010: Detector removal tool without pole.
XP-4: Extension pole for XR2B. Comes in three 5-foot (1.524
m) sections.