Asus NCLV-D - Manual (Page 52)

2 - 3 2 2 - 3 2 2 - 3 2 2 - 3 2 2 - 3 2 C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
4 . 4 . 4 . 4 . 4 . S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 , S e r i a l A T A R A I D c o n n e c t o r s ( 7 - p i n S A T A _ R A I D 1 ,
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 )
S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 ) S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 ) S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 ) S A T A _ R A I D 2 , S A T A _ R A I D 3 , S A T A _ R A I D 4 )
These connectors are for Serial ATA signal cables. These connectors
support up to four Serial ATA hard disk drives that you can configure
as a disk array through the onboard Adaptec AIC-8130 SATA RAID
controller.
• The SATA RAID connectors are available with the NCLV-DA model
only.
• Before creating a RAID set using Serial ATA hard disks, make sure
that you have connected the Serial ATA signal cable and installed
Serial ATA hard disk drives; ; otherwise, you cannot enter the RAID
utility and SATA BIOS setup during POST.
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack 1 before using Serial ATA hard disk drives.
• Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
• When using the connectors in S S S S S tandard IDE t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E mode, connect the
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection
C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r S e t t i n g S e t t i n g S e t t i n g S e t t i n g S e t t i n g U s e U s e U s e U s e U s e
S A T A 1 S A T A 1 S A T A 1 S A T A 1 S A T A 1 M a s t e r M a s t e r M a s t e r M a s t e r M a s t e r B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k
S A T A 2 S A T A 2 S A T A 2 S A T A 2 S A T A 2 S l a v e S l a v e S l a v e S l a v e S l a v e D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k
NCLV-DA SATA RAID connectors
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA_RAID1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA_RAID2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA_RAID3
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
SATA_RAID4