Badgermeter, inc – Badger Meter Series 320 Pulse Transmitter User Manual

Page 4

Due to continuous research, product improvements and enhancements, Badger

Meter reserves the right to change product or system specifications without notice,

except to the extent an outstanding contractual obligation exists.

BadgerMeter, Inc.

P.O. Box 581390, Tulsa, Oklahoma 74158
(918) 836-8411 / Fax: (918) 832-9962
www.badgermeter.com

Please see our website at

www.badgermeter.com

for specific contacts.

Badger

and Data Industrial

are registered trademarks of Badger Meter, Inc.

Model 320 Specifications

Power:

12-35 VDC +/- 5%

12-24 VAC +/- 10%

reverse and over voltage protected to 40VDC

Input Frequency:

0.4 to 10 KHz

Transient Suppression:

Complies with IEC-801-4 electrical burst, fast tran-

sient specification.

Pulse Output:

Isolated solid state switch in any standard or

custom flow total units adjustable 50 mS to 1.0 second

pulse output width in 50 mS increments.

maximum sinking current: 100mA @ 36 VDC

Temperature:

operating: -20°F to 158°F (-29°C to 70°C)

storage: -40°F to 185°F (-40°C to 85°C)

Warranty

Data Industrial Corporation (“Seller”) of 11 Industrial

Drive, Mattapoisett, Massachusetts 02739-0740,

U.S.A., warrants to the original purchaser of its prod-

uct that such product manufactured by Data Industrial

Corporation shall be free from defects in materials or

workmanship when installed, serviced and operated

according to Data Industrial Corporation instructions or

in other such normal use. This warranty is effective for

a period of 12 months from the date of installation by

the Purchaser or 18 months from the date of shipment

by the “Seller” whichever occurs or terminates first. This

limited warranty does not cover damage or loss result-

ing from corrosion or erosion caused by acids or other

chemicals or by severe environmental conditions or

negligent or improper installation or improper operation,

misuse, accident, unauthorized repair or substitution of

components other than those provided by the “Seller”,

and does not cover limited life components such as

bearings, shafts, impellers where wear rate is a function

of application and environment. Any component not

manufactured by the “Seller” but included in its products

shall not be covered by this warranty and is sold only

under such warranty as the manufacturer may provide.

If Buyer or Purchaser wishes to make a claim hereun-

der, he shall send written notice of any defect within

the warranty period, to “Seller” at the above address.

“Seller” may at its sole option instruct Buyer to ship

subject part, postage prepaid, to the “Seller” at above

address or authorize a representative to inspect the part

on site. “Seller” will at its sole option repair or replace

any defective product covered by this warranty. If Buyer

makes repairs or alterations to any product or part

covered by this warranty without “Sellers” prior written

approval, this warranty shall be null and void.

The foregoing shall constitute Buyers or Purchasers

sole and exclusive remedy against “Seller”, and no

other remedy, including but not limited to, incidental

or consequential damages for personal injury, loss of

fluids, gases or other substances or for loss of profits

or injury to property or person shall be available to the

Buyer or Purchaser. The warranty extended herein

shall be in lieu of any other implied warranty of mer-

chantability or fitness for a particular purpose, and seller

shall bear no liability for representatives or retail sellers.

In no event shall Data Industrial Corporation be liable

for any contingent, incidental, or consequential damage

or expenses due to partial or complete inoperability of

its product.

the copyrights hereon may be reproduced or copied

in any form or by any means - graphic, electronic, or

mechanical, including photocopying, recording, taping,

or information and retrieval systems -- without written

permission of Data Industrial.