Seametrics iMAG-Series - Manual (Page 15)

Page 13
CHANGING FLOWMETER SETTINGS
The HOME Screen. The HOME Screen shown below is the
normal screen which displays TOTAL flow volume and flow RATE
along with status conditions such as Empty Pipe. Two buttons
below the LCD display are used to access menu screens for
viewing and changing meter setup parameters.
Button Sensors. The two buttons are light sensors which can
detect when a finger is covering them. Only three button touch
actions are needed to control navigation through the menus,
settings changes and back to the home screen. They are:
Main Menu. All menu screens consist of two rows of tabs
surrounding a dialog box that lets you view and change setup
parameters. For the MAIN MENU, the tabs have the following
functions:
To enter the MAIN MENU perform the hold and tap se-
quence:
Once in the main menu you can move from tab to tab by
tapping the button:
In the dialog box for the currently highlighted tab you will
see that tab parameter’s current value. In the previous
screen illustration, the first line indicates that the cur-
rent unit for the TOTAL is GALLONS. The next two lines in
the dialog box tell you what to do next. If you would like
to change the TOTAL units, just perform the hold and tap
sequence to bring up a dialog box that will
tell you how to change the setting.
You select the new setting by scrolling through a list of
selections as in the screen illustration below by tapping
to find a different TOTAL unit.
Similiarly, for the SET tabs, the dialog box instructions will
tell you how to change a numerical value using both the
and buttons.
To accept any changes you’ve made just hold and tap
again, and the changes will be saved and you will be
returned to the MAIN MENU screen where you can move to
another tab.
When you are finished making changes, move to the EXIT
tab using:
To return to the HOME screen, hold and tap:
Submenu. The EXIT tab in the MAIN MENU has a second
function. If, instead of using the hold and tap sequence to
return to the HOME screen, you tap four times.
You will be redirected to a SUBMENU screen which pro-
vides access to more information about the meter, such
Serial Numbers and firmware revisions. Navigation in this
SUBMENU is the same as for the MAIN MENU. Whenever
you wish, go to the EXIT tab in the SUBMENU and use the
hold and tap sequence to return to the MAIN
MENU.
Please Note:
All iMAG meters are factory set for gallons per minute (GPM) rate and gallons total. If other
units are required, they can be programmed in the field.
Hold
Tap
+
HORIZONTAL SCROLLING : Tap right-hand button
to scroll horizontally through menu tabs or move
horizontally within a tab dialog when applicable.
Hold
Tap
+
SELECT : Tap left-hand button to change a highlighted
item within a tab dialog.
Hold Tap
+
ENTER/EXIT : Hold left button while tapping
right button once to enter or exit a tab dialog
or to navigate between the HOME and other
menu screens.
INPUTS/OUTPUTS and OPERATION
1.2345678
100
TOTAL
CU FT
X1000
RATE
GPM
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
TOTAL = GALLONS
PRESS + TO SET TOTAL
UNITS FOR DISPLAY
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
TOTAL:
PRESS TO CHANGE
GALLONS
1.2345678
100
TOTAL
CU FT
X1000
RATE
GPM
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
TOTAL = GALLONS
PRESS + TO SET TOTAL
UNITS FOR DISPLAY
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
TOTAL:
PRESS TO CHANGE
GALLONS
TAB FUNCTION
T UNIT View or change TOTAL volume units
R UNIT View or change flow RATE units
SET P View or change pulse output scaling
DAMP View or change filter settings
SET 4 View or change flow rate corresponding to 4mA
SET 20 View or change flow rate corresponding to 20mA
SET F View or change high frequency output scaling
Selections are: 500 Hz, 1 KHz, 2 KHz, 5 KHz & 10 KHz
EXIT Return to HOME SCREEN or Enter SUBMENU
Hold Tap
+
Hold
Tap
+
Hold Tap
+
Hold
Tap
+
Hold
Tap
+
Hold
Tap
+
Hold
Tap
+
Hold Tap
+
Hold
Tap
+
Hold Tap
+
1.2345678
100
TOTAL
CU FT
X1000
RATE
GPM
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
TOTAL = GALLONS
PRESS + TO SET TOTAL
UNITS FOR DISPLAY
T UNIT R UNIT SET P DAMP
SET 4 SET 20 SET F EXIT
TOTAL:
PRESS TO CHANGE
GALLONS