beautypg.com

Universal Air Tools UT190R (3/16) User Manual

Foreseen use of the tool, Putting into service air supply, Operator instructions important

background image

Kg

lbs

UT180R

2.00

4.40

UT190R

1.80

3.96

Personal Safety Equipment

Use - Safety Glasses

Yes

Use - Safety Gloves
Use - Safety Boots
Use - Breathing Masks
Use - Ear Protectors

Air Pressure

Recommended Working

6.3

bar

90

PSI

Recommended Minimum

n/a

bar

n/a

PSI

Maximum

7.0

bar

100

PSI

Manufacturer/Supplier

Product Type

RPM

Cycles Per Min

Tel No

Fax No

(01494) 883300

(01494) 883237

Model No/Nos

Serial No

Product Nett Weight

Recommended Use Of

Balancer Or Support

Recommended Hose Bore

Size - Minimum

Recommended Max.

Hose Length

Ins

M/M

Ft

M

Foreseen Use of the Tool

This tool is designed to place blind rivets, also known as pop rivets in
pre-formed holes in sheet metal. The rivets are set in the sheet by a
pulling force exerted by the tool under the action of a hydro-pneumatic
cylinder. Upon placing the rivet correctly in the sheet, the stem of the
blind rivet will break off when the rivet is placed. Do not use the tool for
any other purpose than that for which it was designed unless first
consulting the manufacturer or the manufacturer’s authorised
representative.
Do not modify the tool for any other purpose or its use as a blind rivet
installation tool without first consulting the manufacturer or the
manufacturer’s representative.

Putting Into Service
Air Supply

Use a clean lubricated air supply that will give a measured air pressure
at the tool of 90 p.s.i./6.3 bar when the tool is running with the trigger
fully depressed. Use recommended hose size and length. It is
recommended that the tool is connected to the air supply as shown in
figure 1. Do not connect the tool to the air line system without
incorporating an easy to reach and operate air shut off valve. The air
supply should be lubricated. It is strongly recommended that an air filter,
regulator, lubricator (FRL) is used as shown in Figure 1 as this will supply
clean, lubricated air at the correct pressure to the tool. Details of such
equipment can be obtained from your supplier. If such equipment is not
used then the tool should be lubricated by shutting off the air supply to
the tool, depressurising the line by pressing the trigger on the tool.
Disconnect the air line and pour into the intake bushing a teaspoonful
(5ml) of a suitable pneumatic motor lubricating oil preferably
incorporating a rust inhibitor. Reconnect tool to air supply and run tool

No

Page No 1

Air Hydraulic Blind Riveter
(Vacuum System)

UT180R (1/4”)
UT190R (3/16”)

3/8

10

30

10

Includes - Foreseen Use, Work Stations, Putting Into Service, Operating,
Dismantling, Assembly and Safety Rules

Operator Instructions

Important

Read these instructions carefully before installing, operating,
servicing or repairing this tool. Keep these instructions in a safe
accessible place.

Universal Air Tool Company Limited

Unit 8

Lane End Industrial Park

High Wycombe

Bucks

HP14 3BY

Vibration Level

Test Method

Tested in accordance with ISO

standards 8662 Part 1

Less than 2.5

Noise Level

Sound Pressure Level 70.5 dB(A)

Test Method

Tested in accordance with Pneurop

test code PN8NTC1 and ISO Standard 3744

Sound Power Level 82.4 dB(A)

Work Stations

The tool should only be used as a handheld, hand operated tool. It is
always recommended that the tool is used when standing on a solid
floor. It can be
used in other
positions

but

before any such
use, the operator
must be in a
secure position
having a firm grip
and footing and
be aware of a
reaction force on
the hand as
result of the tool
doing work.

Metres / Sec²

This manual is related to the following products: